Suitable for use on FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol VIPA-SP & SFC baseplates. Finally, because the reaction point for the installation tool has been moved to the head of the rail, the installer is able to lift sleepers (about 20mm) as part of the normal action of the tool, lifting from the rear arches of the clip before driving the clip into the installed position. NOTE: This tool has options avaialble under separate reference numbers; for variants with either insulated handles and / or cranked heads for confined spaces. The standard tool is always supplied with a straight head and steel handle. Optional variant of this tool using cranked head for confined spaces and insulated handle To insert the clips from the ‘Parked’ position of the shoulder as delivered from the sleeper factory, follow these instructions. The paddle should be in the normal front pivot hole and the side cheeks in the down position. (Different from the photograph) for ALL rail sizes. Locate the hooks on the side arms over the head of the rail. To insert the clips, grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip driving. Pull on the handle until refusal. The fully driven position for FASTCLIP ‘FC’ is achieved when the outer legs of the clip touch the rear of the side insulator in the shoulder, or with up to 3 mm of clearance. The FASTCLIP ‘FE’ installed position does NOT touch the shoulder or insulator. Once located the tool can be slid along the rail between sleepers for the next clip insertion. If the clip needs to be re-inserted from fully extracted, move the cheeks to the up position, to extend the reach of the tool. If more reach is required, the paddle can be moved to the rear pivot hole. Follow the instructions above.

Insulated Square Mouth Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 8" Wide By 10.1/2" Long

Tested For Live Work Used for shovelling out or concrete mixing, working tarmac and cement, backfilling trenches and manouvering ballast.

Insulated Taper Mouth Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 10" Wide By 8.1/2" Tapering To 12.1/2" Long

Tested For Live Work Used for shovelling out or concrete mixing, working tarmac and cement, backfilling trenches and manouvering ballast.

Insulated Clay Grafting Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 6" Wide By 12" Long T

ested For Live Work With a slightly dished blade and round cutting edge, designed for clay digging and heavy ground breaking.

Insulated Cable Laying Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 5" Wide Tapering to 4.1/2" By 11"

Long Tested For Live Work Often known as a '1-way' in some trades.

Designed for cable and pipe laying with a slim blade that is ideal for digging out narrow trenches.

This all steel grafting tool has a dished blade and a curved cutting edge which makes it ideal for clay digging and heavy ground breaking work.
It has a forged blade, tubular steel shaft and steel YD grip with wooden cross piece for added comfort.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE: 6" WIDE X 12" LONG

This all steel Newcastle draining shovel has a forged blade, tubular steel shaft and steel YD grip with wooden cross piece for added comfort.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE : 7" WIDE, TAPERING TO 4" BY 16" LONG

This all steel round mouth shovel has a forged blade, tubular steel shaft and steel YD grip with wooden cross piece for added comfort.

Used for excavating, digging and shovelling most aggregates. The pointed blade offers easier penetration in tougher ground.

PRODUCT HANDLE: 28"/ 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE: 10" WIDE X 12.1/2" LONG

Solid Steel Crowbar with Chisel & Point Ends - 28mm Round X 1500mm Shaft

• Insulated Heel & Point Crowbar
• 60" Insulated Solid, Non-Conductive Fibreglass Shaft with Forged Steel Ends
• Conforms to BS8020
• Quote MM0001 when ordering over the phone to receive our special price of £35 (exc vat)
• Tested up to 10000V
• Safe for up to 1000V 
• 1.5M 
• 6KG