Insulated Treaded Round Mouth Shovel Shovel

Treaded

Tested And Certified To BS8020:2011

Handle - 28" / 711mm Blade Size - 10" Wide By 12.1/2" Long

Tested For Live Work

Used for excavating, diggiing and sovelling most aggregates. The pointed blade offers easier penetration in tougher ground.

Catalogue No; Reference: 0039/42748 PANDROL No. LP1180. And for 4 shoulder baseplates. All STEL hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 32 mm diameter cylindrical straight handles, Instructions for PANPULLER LP1180 ​• Insert center leg of clip into housing. • Place pivoted hook over the inside of the front arch of clip with foot of PANPULLER behind clip housing and ensure lip of the hook is under the front arch. • Taking up a natural stance with feet apart, move one leg half a pace back to prevent loss of balance. Stand behind the PANPULLER, with both hands on tee handle at top of PANPULLER, pull strongly towards chest until refusal. • The PANPULLER automatically pulls clip to the correct position Extraction Instructions Reverse the PANPULLER • Taking up a natural stance (feet apart, move one leg half a pace back to prevent loss of balance) on the same side as for installation, place hook on the outside of the front arch of the clip, the foot of the PANPULLER resting on the baseplate/housing just above the centre leg of clip (as illustrated). • Standing behind PANPULLER with both hands on the tee handle at the top of PANPULLER, give a strong firm push away from your chest. • If clips have been in situ for many years, it may be necessary to use a hammer to loosen them taking safety precautions. If the clips will not move then use the Rusty Clip Extractor can be used for PR clips. NOTE. It is mandatory to wear eye protection when removing or fitting any clips where hammer assistance might be necessary.

• Magnetic Retrieving Baton with Release.
• Magnetic Retrieving Batons are innovative and powerful tools to remove ferrous materials in wet or dry environments.
• Non-corrosive, stainless steel.
• Use of safety goggles and gloves is highly recommended when using this item.
• Ideal for removing hardware from storage bins.
• Clean water or degreasing tanks of metal shavings.
• Unique shape allows for easy pick up from walls and corners.
• Constructed with neodymium/rare earth magnets to maximize holding power.
• Pull to release collected material to dispose of.

All Steel Extractor Ferrule

• Conforms to BS8020 : 2011
• Keying Hammer Head - 10lb / 4.5kg
• Fiberglass Shaft
• Rubber Grip Handle
• Steel Protective Collar
• Overall Length - Approximately 92.5cm

Similar in design to the nine prong compost fork but more suited to heavy-duty work, the ballast fork is ideal for: Moving and loading stone, ballast and tarmac. Use by railway workers to transfer roadbed ballast.

Cat No; Reference: 0039/42900 The PANSETTER is suitable for all Network Rail Sleepers fitted with PR, e & e-PLUS. Used for lifting the sleeper to the rail foot. It pushes the rail over, leaving the correct gap between the rail foot and the Pandrol housing, so that the insulator can be easily placed in the correct position. All Pandrol hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 35mm diameter cylindrical handles with ‘T’ cross bars for improved ergonomic and safer use.

It is recommended for safety reasons that contractors should formally check and record the wear of the hooks at intervals of 6 months using the wear gauge.
The gauge is suitable for all types of Panpuller or e-Plus Panpuller.
The wear gauge provides easy Go/No-Go assessment of when to replace the hook.
Work hooks have a tendency to slip off the clips, which can present a significant risk to operators.

• Timber Nips used for the safe manual handling and movement of Timber Sleepers.
• A durable and robust tool

• Tongs used for the safe manual handling and moving of Steel Sleepers.
• Built to be both durable and robust, they allow the rail worker to use them to re-position and remove steel sleepers as required.
• Insulated to BS8020.