Suitable for use on FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol VIPA-SP & SFC baseplates. Finally, because the reaction point for the installation tool has been moved to the head of the rail, the installer is able to lift sleepers (about 20mm) as part of the normal action of the tool, lifting from the rear arches of the clip before driving the clip into the installed position. NOTE: This tool has options avaialble under separate reference numbers; for variants with either insulated handles and / or cranked heads for confined spaces. The standard tool is always supplied with a straight head and steel handle. Optional variant of this tool using cranked head for confined spaces and insulated handle To insert the clips from the ‘Parked’ position of the shoulder as delivered from the sleeper factory, follow these instructions. The paddle should be in the normal front pivot hole and the side cheeks in the down position. (Different from the photograph) for ALL rail sizes. Locate the hooks on the side arms over the head of the rail. To insert the clips, grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip driving. Pull on the handle until refusal. The fully driven position for FASTCLIP ‘FC’ is achieved when the outer legs of the clip touch the rear of the side insulator in the shoulder, or with up to 3 mm of clearance. The FASTCLIP ‘FE’ installed position does NOT touch the shoulder or insulator. Once located the tool can be slid along the rail between sleepers for the next clip insertion. If the clip needs to be re-inserted from fully extracted, move the cheeks to the up position, to extend the reach of the tool. If more reach is required, the paddle can be moved to the rear pivot hole. Follow the instructions above.

Insulated Treaded Round Mouth Shovel Shovel

Treaded

Tested And Certified To BS8020:2011

Handle - 28" / 711mm Blade Size - 10" Wide By 12.1/2" Long

Tested For Live Work

Used for excavating, diggiing and sovelling most aggregates. The pointed blade offers easier penetration in tougher ground.

Catalogue No; Reference: 0039/42748 PANDROL No. LP1180. And for 4 shoulder baseplates. All STEL hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 32 mm diameter cylindrical straight handles, Instructions for PANPULLER LP1180 ​• Insert center leg of clip into housing. • Place pivoted hook over the inside of the front arch of clip with foot of PANPULLER behind clip housing and ensure lip of the hook is under the front arch. • Taking up a natural stance with feet apart, move one leg half a pace back to prevent loss of balance. Stand behind the PANPULLER, with both hands on tee handle at top of PANPULLER, pull strongly towards chest until refusal. • The PANPULLER automatically pulls clip to the correct position Extraction Instructions Reverse the PANPULLER • Taking up a natural stance (feet apart, move one leg half a pace back to prevent loss of balance) on the same side as for installation, place hook on the outside of the front arch of the clip, the foot of the PANPULLER resting on the baseplate/housing just above the centre leg of clip (as illustrated). • Standing behind PANPULLER with both hands on the tee handle at the top of PANPULLER, give a strong firm push away from your chest. • If clips have been in situ for many years, it may be necessary to use a hammer to loosen them taking safety precautions. If the clips will not move then use the Rusty Clip Extractor can be used for PR clips. NOTE. It is mandatory to wear eye protection when removing or fitting any clips where hammer assistance might be necessary.

Insulated Newcastle Treaded Shovel

Tested And Certified To BS8020:2011

Treaded Tested For Live Work 16" Long, 7" Wide Tapering to 4"

Often known as a 'grafter' in some trades.

Designed for digging deep and narrow trenches, channels and post holes.

Insulated Trenching Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 7" Wide x 11" Long

Tested For Live Work Often known as a '2-way' in some trades Used for digging and cleaning out narrow trenches for cable and pipe laying

1 11/16" Bi-Square Fishplate Nut Spanner
36" BS8020 Fibreglass Insulated Shaft

Insulated Check Rail Spanner - 1-11/16" AF x 30" L
Insulated to BS8020

Rail Turning Bar - Insulated Bull Head
Insulated to BS8020

Insulated Hook Switch Pole
Insulated to BS8020

• Conforms to BS8020 : 2011
• Keying Hammer Head - 10lb / 4.5kg
• Fiberglass Shaft
• Rubber Grip Handle
• Steel Protective Collar
• Overall Length - Approximately 92.5cm