Insulated Treaded Round Mouth Shovel Shovel

Treaded

Tested And Certified To BS8020:2011

Handle - 28" / 711mm Blade Size - 10" Wide By 12.1/2" Long

Tested For Live Work

Used for excavating, diggiing and sovelling most aggregates. The pointed blade offers easier penetration in tougher ground.

Catalogue No; Reference: 0039/42748 PANDROL No. LP1180. And for 4 shoulder baseplates. All STEL hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 32 mm diameter cylindrical straight handles, Instructions for PANPULLER LP1180 ​• Insert center leg of clip into housing. • Place pivoted hook over the inside of the front arch of clip with foot of PANPULLER behind clip housing and ensure lip of the hook is under the front arch. • Taking up a natural stance with feet apart, move one leg half a pace back to prevent loss of balance. Stand behind the PANPULLER, with both hands on tee handle at top of PANPULLER, pull strongly towards chest until refusal. • The PANPULLER automatically pulls clip to the correct position Extraction Instructions Reverse the PANPULLER • Taking up a natural stance (feet apart, move one leg half a pace back to prevent loss of balance) on the same side as for installation, place hook on the outside of the front arch of the clip, the foot of the PANPULLER resting on the baseplate/housing just above the centre leg of clip (as illustrated). • Standing behind PANPULLER with both hands on the tee handle at the top of PANPULLER, give a strong firm push away from your chest. • If clips have been in situ for many years, it may be necessary to use a hammer to loosen them taking safety precautions. If the clips will not move then use the Rusty Clip Extractor can be used for PR clips. NOTE. It is mandatory to wear eye protection when removing or fitting any clips where hammer assistance might be necessary.

Insulated Trenching Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 7" Wide x 11" Long

Tested For Live Work Often known as a '2-way' in some trades Used for digging and cleaning out narrow trenches for cable and pipe laying

15" Fishplate Nut Running Spanner, used for the quick release of fish plate nuts. The length of the handle allows the railway worker to quickly remove or tighten the nuts.

• Conforms to BS8020
• Certified to 1000 Volts - Tested to 10000 Volts
• Solid forged from one piece of steel
• YD handle
• Strong yet lightweight fibreglass shaft has excellent insulating properties
• Lightweight at just 2.5kg
• BS8020:2011

No. AE17256 formerly No. LP15923

Colour: White

The tool is used with the eP20129 green or eP20130 yellow e-PLUS clips, mostly with RT60 and NR60 S&C layouts.

Cat No Reference: 0039/47852 Suitable for use on FASTCLIP FC and FASTCLIP FE The original version of the sleeper lifter can still be used in conjunction the new installer where sleepers need to be lifted more than 20mm. Instructions for Sleeper Lifter LP12608 The scissor action of the frame opens in order to locate the pincers of the tool into the sides of the shoulder with the clip in the ‘Parked’ position. Place the hook of the tool over the head of the rail, and as the body of the tool rises the scissor action closes the pincers and lock into the shoulder. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during sleeper lifting. Push the handle away to lift any ‘dropped’ sleeper if ballast conditions do not support the sleepers engaging with the foot of the rail. These tools should be used in pairs to lift the sleeper to locate both rails simultaneously with the rail seats of the sleeper. The sleeper lifter can used on the same rail seat as the FASTCLIP installer, by locating between the hooks of the installation tool.

Rear arch extractor for FASTCLIP ‘FC PANDROL No. LP15177 The rear arch extractor remains available to extract clips around IBJ’s. This tool is ONLY needed at IBJ’s in order to extract clips which are shielded by the scalloped section of the joint. It is also unique to FASTCLIP ‘FC’ and does NOT work with ‘FE’ clips. Instructions for Rear Arch Extractor The hooks in the frame of the tool locate into the reaction points on the shoulder, as shown in the photograph. The clip is extracted using the tines inserted in the rear arches of the clip. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip extraction. Push the handle away to extract the clip, stopping at the ‘Parked’ position, or continuing to push away to fully extract the clip from the shoulder.

All Steel Square Mouth Shovel intended for shoveling out, concrete mixing, working tarmac as well as cement, back filling trenches and maneuvering ballast.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE: 10'' WIDE X 12.1/2" LONG

This all steel rabbit shovel has a forged blade, tubular steel shaft and steel YD grip with wooden cross piece for added comfort.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: 7" TO 5"X 12"

Length 112cm
Width 15cm
Weight 2.5kg