Rear arch extractor for FASTCLIP ‘FC PANDROL No. LP15177 The rear arch extractor remains available to extract clips around IBJ’s. This tool is ONLY needed at IBJ’s in order to extract clips which are shielded by the scalloped section of the joint. It is also unique to FASTCLIP ‘FC’ and does NOT work with ‘FE’ clips. Instructions for Rear Arch Extractor The hooks in the frame of the tool locate into the reaction points on the shoulder, as shown in the photograph. The clip is extracted using the tines inserted in the rear arches of the clip. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip extraction. Push the handle away to extract the clip, stopping at the ‘Parked’ position, or continuing to push away to fully extract the clip from the shoulder.

Fastclip Installation Tool F41/G44/EG47 Cat No. 0039/047850 RB/BR/123 Suitable for all steel and concrete sleeper types. The installation tool has two functions, each achieved by simply re-positioning a moveable pin. With the pin passing through the rear hole of the claw, installation of a Pandrol Fastclip assembly in the ‘switched off’ position is carried out. When the pin is re-positioned to the front hole of the claw and the installation operation repeated, the assembly will be in the ‘switched on’ position.

Cat No; Reference: 0039/42900 The PANSETTER is suitable for all Network Rail Sleepers fitted with PR, e & e-PLUS. Used for lifting the sleeper to the rail foot. It pushes the rail over, leaving the correct gap between the rail foot and the Pandrol housing, so that the insulator can be easily placed in the correct position. All Pandrol hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 35mm diameter cylindrical handles with ‘T’ cross bars for improved ergonomic and safer use.

• Keying Hammer Head - 10lb / 4.5kg
• Hickory Handle
• Overall Length - Approximately 91.5cm

Designed to be used singularly or in pairs, for the lifting and transportation of lengths or rail, or parts of points and crossings from one location to another. The Ironman can also be used to transpose rail from one side of the track to the other. Therefore by straddling the running rails, access to the four-foot, six-foot and cess is possible.

Designed to be used singularly or in pairs, for the lifting and transportation of lengths or rail, or parts of points and crossings from one location to another.

The Ironman can also be used to transpose rail from one side of the track to the other. Therefore by straddling the running rails, access to the four-foot, six-foot and cess is possible.

POA

• An innovative removable rechargeable battery system is used giving extended battery life. 
• A battery is supplied with each new unit. 
• Single or 5 way intelligent chargers are available that allow the battery packs to be left on charge all the time, without over charging, enabling battery packs to be ready for use at all times.

• Graphite cast iron load sheave
• Hand lever made of malleable cast iron or tubular steel model with rubber grip
• Automatically acting load pressure brake
• Free chaining device optional
• Drop forged load and suspension hooks
• Asbestos-free friction discs

Yale Hand Lever Hoists are versatile, portable units for pulling, tensioning, lashing and lifting loads. The operation of the Hand Lever Hoists is easy and safe.
Light weight, robust malleable cast iron model, free chaining, slip clutch, stamped steel - or aluminium housing, low operating effort - in the Yale product range you will always find an optimal hoist for every type of operation.
The brake system of all Yale hand lever hoists are based on the original Yale patent of the British Engineer Thomas A Weston dating back to 1875. All parts of the load brake are made of high quality materials and are protected against corrosion.
The graphite cast iron load sheave for the link chain has precision machined chain pockets for accurate fit and durability of the load chain. The roller chain sprocket is made from heat treated chromium-molybdenum steel with precision machine teeth to ensure smooth chain movement.
Every Yale ratchet lever hoist is factory tested with overload. The units are supplied with a test certificate showing the serial-No. Operating instructions which contain an EC declaration of conformity are also attached to each unit.

The VSR is designed to attach to the rail fastening, and by means of a rotating lift arm and bearing, contact the underside of the rail head and lift the rail from the sleeper (tie).
Once lifted, the rail can be moved with very low friction for the purposes of rail stressing, the resultant excellent stress distribution is therefore optimised.
The VSR can also be used for changing rail pads and the e-clip product has been designed with extra lift for that specific purpose.

The Vortok Fastclip Stressing Roller is designed to attach to the rail fastening, and by means of a rotating lift arm and bearing, contact the underside of the rail head and lift the rail from the sleeper (tie).
Once lifted, the rail can be moved with very low friction for the purposes of rail stressing, the resultant excellent stress distribution is therefore optimised.
The VSR can also be used for changing rail pads and the e-clip product has been designed with extra lift for that specific purpose.