• Hi-Vis Chainsaw Trousers (XL)
• Elasticated waist
• Stretch Material in crotch for easy movement
• 1 x velcro back pocket
• 1 x velcro side pocket
• Type C CLASS 1 Protection Conforms to EN381-5 20m/s
• EN471 : 2004 class 2
• Internal side seem to prevent snagging
• Zip fly
• Eight layers of all round protection
• Buttons for braces and kidney flap for comfort
• Ultra light pro trouser
• Reflective hi-viz stripes 7cm

Suitable for use on FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol VIPA-SP & SFC baseplates. Finally, because the reaction point for the installation tool has been moved to the head of the rail, the installer is able to lift sleepers (about 20mm) as part of the normal action of the tool, lifting from the rear arches of the clip before driving the clip into the installed position. NOTE: This tool has options avaialble under separate reference numbers; for variants with either insulated handles and / or cranked heads for confined spaces. The standard tool is always supplied with a straight head and steel handle. Optional variant of this tool using cranked head for confined spaces and insulated handle To insert the clips from the ‘Parked’ position of the shoulder as delivered from the sleeper factory, follow these instructions. The paddle should be in the normal front pivot hole and the side cheeks in the down position. (Different from the photograph) for ALL rail sizes. Locate the hooks on the side arms over the head of the rail. To insert the clips, grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip driving. Pull on the handle until refusal. The fully driven position for FASTCLIP ‘FC’ is achieved when the outer legs of the clip touch the rear of the side insulator in the shoulder, or with up to 3 mm of clearance. The FASTCLIP ‘FE’ installed position does NOT touch the shoulder or insulator. Once located the tool can be slid along the rail between sleepers for the next clip insertion. If the clip needs to be re-inserted from fully extracted, move the cheeks to the up position, to extend the reach of the tool. If more reach is required, the paddle can be moved to the rear pivot hole. Follow the instructions above.

Reduced shank for smaller diameter cutters

• Insulated Heel & Point Crowbar
• 60" Insulated Solid, Non-Conductive Fibreglass Shaft with Forged Steel Ends
• Conforms to BS8020
• Quote MM0001 when ordering over the phone to receive our special price of £35 (exc vat)
• Tested up to 10000V
• Safe for up to 1000V 
• 1.5M 
• 6KG

Light Weight "YELLOW" - Standard Strength PADS
The utilisation of new magnet material technology has enabled the dramatic reduction to the overall weight of the actual magnet unit, therefore developing a much more simplified track fixing procedure.
Single line attachment has been the key to significantly reducing the installation time, now approximately 30 seconds from stepping into the 4ft.
As stipulated by Network Rail each unit can be padlocked to deter vandals.

Please Call For Parts List 0114 383 0110 or Email sales@specialisedtools.co.uk 

OUTPUT: 3.4kVA / 2.7kW
SOCKETS: 1 x 16a 115v / 1 x 32a 115v / 2 x 16a 230v
ENGINE: Honda GX200
HP/CYLINDERS: 6.5 / 1
START: Recoil
FUEL TANK: 3.1 Litres
RUN TIME: 2.5 Hours
NOISE LEVEL: 71dBA @ 7 metres
DIMENSIONS: L610 x W420 x H415mm
WEIGHT: 36 KG
OPTIONS: Single voltage, LPG conversion, Long run tank (metal), Trolley kit.

SHOVEL, RABBIT / POST HOLE INSULATED HEAD SIZE 5-1/2" X 12" LONG 54" HANDLE, OVERALL LENGTH 72"

SUMO, BUILDERS / FENCING INSULATED SPADE 54" LONG HANDLE, OVERALL LENGTH 72" HEAD SIZE 5-1/2" X 14" LONG

13mm M42 Rail Cutter Short Series

14mm M42 Rail Cutter Short Series