JACK HANDLE A17 SIMPLEX @ 1200MM LONG WHITE ROUND METAL HANDLE, NEW VERSION

E Clip Replacement Hook 0039/42743

Suitable for use on FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol VIPA-SP & SFC baseplates. Finally, because the reaction point for the installation tool has been moved to the head of the rail, the installer is able to lift sleepers (about 20mm) as part of the normal action of the tool, lifting from the rear arches of the clip before driving the clip into the installed position. NOTE: This tool has options avaialble under separate reference numbers; for variants with either insulated handles and / or cranked heads for confined spaces. The standard tool is always supplied with a straight head and steel handle. Optional variant of this tool using cranked head for confined spaces and insulated handle To insert the clips from the ‘Parked’ position of the shoulder as delivered from the sleeper factory, follow these instructions. The paddle should be in the normal front pivot hole and the side cheeks in the down position. (Different from the photograph) for ALL rail sizes. Locate the hooks on the side arms over the head of the rail. To insert the clips, grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip driving. Pull on the handle until refusal. The fully driven position for FASTCLIP ‘FC’ is achieved when the outer legs of the clip touch the rear of the side insulator in the shoulder, or with up to 3 mm of clearance. The FASTCLIP ‘FE’ installed position does NOT touch the shoulder or insulator. Once located the tool can be slid along the rail between sleepers for the next clip insertion. If the clip needs to be re-inserted from fully extracted, move the cheeks to the up position, to extend the reach of the tool. If more reach is required, the paddle can be moved to the rear pivot hole. Follow the instructions above.

Catalogue No; Reference: 0039/42748 PANDROL No. LP1180. And for 4 shoulder baseplates. All STEL hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 32 mm diameter cylindrical straight handles, Instructions for PANPULLER LP1180 ​• Insert center leg of clip into housing. • Place pivoted hook over the inside of the front arch of clip with foot of PANPULLER behind clip housing and ensure lip of the hook is under the front arch. • Taking up a natural stance with feet apart, move one leg half a pace back to prevent loss of balance. Stand behind the PANPULLER, with both hands on tee handle at top of PANPULLER, pull strongly towards chest until refusal. • The PANPULLER automatically pulls clip to the correct position Extraction Instructions Reverse the PANPULLER • Taking up a natural stance (feet apart, move one leg half a pace back to prevent loss of balance) on the same side as for installation, place hook on the outside of the front arch of the clip, the foot of the PANPULLER resting on the baseplate/housing just above the centre leg of clip (as illustrated). • Standing behind PANPULLER with both hands on the tee handle at the top of PANPULLER, give a strong firm push away from your chest. • If clips have been in situ for many years, it may be necessary to use a hammer to loosen them taking safety precautions. If the clips will not move then use the Rusty Clip Extractor can be used for PR clips. NOTE. It is mandatory to wear eye protection when removing or fitting any clips where hammer assistance might be necessary.

Spare Bolt For Pan Puller

SUMO, BUILDERS / FENCING INSULATED SPADE 54" LONG HANDLE, OVERALL LENGTH 72" HEAD SIZE 5-1/2" X 14" LONG

SHOVEL, RABBIT / POST HOLE INSULATED HEAD SIZE 5-1/2" X 12" LONG 54" HANDLE, OVERALL LENGTH 72"

Please Call For Parts List 0114 383 0110 or Email sales@specialisedtools.co.uk 

OUTPUT: 3.4kVA / 2.7kW
SOCKETS: 1 x 16a 115v / 1 x 32a 115v / 2 x 16a 230v
ENGINE: Honda GX200
HP/CYLINDERS: 6.5 / 1
START: Recoil
FUEL TANK: 3.1 Litres
RUN TIME: 2.5 Hours
NOISE LEVEL: 71dBA @ 7 metres
DIMENSIONS: L610 x W420 x H415mm
WEIGHT: 36 KG
OPTIONS: Single voltage, LPG conversion, Long run tank (metal), Trolley kit.

Colour: Red working head (matches the appropriate e-PLUS clip type), and yellow handle. For use with eP20127 clips for retrofitting to sleeper types: F27, EF28, 5EF28, and for the new S&C designs to NR56V. All STEL hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 32mm diameter cylindrical straight handles Installation Instructions • Insert center leg of clip into housing. • Place pivoted hook over the inside of the front arch of clip with foot of PANPULLER behind clip housing and ensure lip of the hook is under the front arch. • Taking up a natural stance with feet apart, move one leg half a pace back to prevent loss of balance. Stand behind the PANPULLER, with both hands on tee handle at top of PANPULLER, pull strongly towards chest until refusal. • The PANPULLER automatically pulls clip to the correct position When correctly installed the centre leg of ALL types of e-PLUS clips, protrude beyond the shoulder to hold the side-insulator in the correct position. This tool is 'handed' to hold the insulator in position during clip insertion. This means that the tool cannot be used for extraction of the clip. To extract this e-Plus clip use a standard PANPULLER Type LP1180

Lighting long stretches of road, rail track or tunnel is now easier and more efficient than ever with the STEL Lucia link light.

• The STEL Lucia LED portable link lighting is perfect for use in the rail industry and construction industry for temporary lighting of access and maintenance projects such as  long stretches of motorway and rail.
• The STEL Lucia LED portable link lighting avoids the expense of bulky lighting equipment with excellent cost savings against tower lights.
• The STEL Lucia LED portable lighting will provide over 500 metres of efficient lighting from a small single 3KVA generator.

Specification:

• Input Voltage: AC 100 - 240 V
• Input Frequency: 50 - 60 h
• Safety Level: Class 1
• Rated Power: 30 Watt
• Lamps Lument: 3600 lms
• Whole Light Angle: 180 °
• Working Temperature: -22°C / +55°C
• Lighting IP Rating: IP67
• Plug IP Rating: IP44
• LED Lifetime: 30,000 hrs
• Size: 64cm x 11cm x 6.5cm
• Weight: 1.3 KG

Please note light mast,basket and extension sold seperately.

Part Codes:

• Lucia LED Light - Code: 410000
• Lucia LED Light Mast: 410024
• Lucia LED Light Basket: 410027