No. AE17256 formerly No. LP15923

Colour: White

The tool is used with the eP20129 green or eP20130 yellow e-PLUS clips, mostly with RT60 and NR60 S&C layouts.

Fastclip Installation Tool F41/G44/EG47 Cat No. 0039/047850 RB/BR/123 Suitable for all steel and concrete sleeper types. The installation tool has two functions, each achieved by simply re-positioning a moveable pin. With the pin passing through the rear hole of the claw, installation of a Pandrol Fastclip assembly in the ‘switched off’ position is carried out. When the pin is re-positioned to the front hole of the claw and the installation operation repeated, the assembly will be in the ‘switched on’ position.

Cat No Reference: 0039/47852 Suitable for use on FASTCLIP FC and FASTCLIP FE The original version of the sleeper lifter can still be used in conjunction the new installer where sleepers need to be lifted more than 20mm. Instructions for Sleeper Lifter LP12608 The scissor action of the frame opens in order to locate the pincers of the tool into the sides of the shoulder with the clip in the ‘Parked’ position. Place the hook of the tool over the head of the rail, and as the body of the tool rises the scissor action closes the pincers and lock into the shoulder. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during sleeper lifting. Push the handle away to lift any ‘dropped’ sleeper if ballast conditions do not support the sleepers engaging with the foot of the rail. These tools should be used in pairs to lift the sleeper to locate both rails simultaneously with the rail seats of the sleeper. The sleeper lifter can used on the same rail seat as the FASTCLIP installer, by locating between the hooks of the installation tool.

Product Code: 0039/047851 Previously LP18679 Suitable for extracting FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol baseplate types VIPA-SP & SFC baseplate. Instructions for Extractor AE17385 The Extractor tool acts as a lever against the web of the rail and the toe of the clip. To locate the tool hold at angle away from the rail and move forwards to position the tool between the rail and the shoulder, with the rear clip catching frame towards the operators foot. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip extraction. Push the handles away until the rear of the clip touches the catching frame, to ensure the clip remains in the shoulder, to locate in the ‘Parked’ position. Care should be taken to maintain the operator’s balance during clip extraction as the handle is pushed away. To remove the clip completely from the shoulder, keep pushing the handle so the frame hinges upwards and the clip is removed from the shoulder.

STEL 20mm M42 Rail Cutter Short Series

Suitable for use on FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol VIPA-SP & SFC baseplates. Finally, because the reaction point for the installation tool has been moved to the head of the rail, the installer is able to lift sleepers (about 20mm) as part of the normal action of the tool, lifting from the rear arches of the clip before driving the clip into the installed position. NOTE: This tool has options avaialble under separate reference numbers; for variants with either insulated handles and / or cranked heads for confined spaces. The standard tool is always supplied with a straight head and steel handle. Optional variant of this tool using cranked head for confined spaces and insulated handle To insert the clips from the ‘Parked’ position of the shoulder as delivered from the sleeper factory, follow these instructions. The paddle should be in the normal front pivot hole and the side cheeks in the down position. (Different from the photograph) for ALL rail sizes. Locate the hooks on the side arms over the head of the rail. To insert the clips, grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip driving. Pull on the handle until refusal. The fully driven position for FASTCLIP ‘FC’ is achieved when the outer legs of the clip touch the rear of the side insulator in the shoulder, or with up to 3 mm of clearance. The FASTCLIP ‘FE’ installed position does NOT touch the shoulder or insulator. Once located the tool can be slid along the rail between sleepers for the next clip insertion. If the clip needs to be re-inserted from fully extracted, move the cheeks to the up position, to extend the reach of the tool. If more reach is required, the paddle can be moved to the rear pivot hole. Follow the instructions above.

• Minimum Space Required in Vehicle
• Support Arm Works as Stabiliser during Loading and Unloading
• Reduce potential injury and fatigue to operator
• Doesn't have any influence on axel counters, even when they are not correctly adjusted (set over height)
• Safe and efficient method of transporting tools and smaller plant equipment to worksite
• Width - 360mm
• Length - 870mm
• Height - 190mm (without push handles fitted)
• Height - 820mm (with push handles fitted)
• Weight - 13.6kg (without push handles fitted)
• Weight - 17.8kg (with push handles fitted) 
• Safe Working Load - (NWR Spec) 250kg
• Safe Working Load - (LU Spec) 75kg
• BS EN 13977:2011 - Railway application - Track - Safety requirements for portable machines and Skate Baskets for construction and maintenance.
• RIS 1701 PLT - Rail Industry Standard for Portable and Transportable Plant Used for Infrastructure Work.

• Hi-Vis Orange Thinsulate Balaclava with Ear Mesh
• 100% Acrylic material
• Offers excellent insulation
• 3M C40 premium Thinsulate
• Ideal for winter use
• One size only

This orange thinsulate balaclava is a thermal product which offers excellent insulation making it ideal for winter weathers. It is extremely warm and comfortable ideal for workwear.

• Insulated Heel & Point Crowbar
• 60" Insulated Solid, Non-Conductive Fibreglass Shaft with Forged Steel Ends
• Conforms to BS8020
• Quote MM0001 when ordering over the phone to receive our special price of £35 (exc vat)
• Tested up to 10000V
• Safe for up to 1000V 
• 1.5M 
• 6KG

JACK HANDLE, ALL STEEL, 1" Ø X 30" LONG SUITS SIMPLEX 85A (RJ85A) JACK