JACK HANDLE, ALL STEEL, 1" Ø X 30" LONG SUITS SIMPLEX 85A (RJ85A) JACK

JACK HANDLE, ALL STEEL, 1-1/4" Ø X 30" LONG SUITS A1022 & DUFF NORTON 1022 0050/571059

28mm x 450mm Hexagon Breaker Point Steel to suit BOSCH GSH2Y and GSH16-28 Breakers. 

• Stainless Steel Nut, Bolt and Washer For Speed Boards

All Steel Pot Dolly Hexagon 19mm

This obstructionless jack is fitted with an overload safety valve and tested to 25% over the rated capacity. The jack is placed under the rail without removal of ballast. Despite its low height of 95mm the jack is capable of a 101mm lift due to its hydraulic telescopic ram. Weight 16.5kg Safe Working Load 10t Closed Height 95mm Stroke Length 101mm n Item code: 09 002 SWL: 10t on head Closed height: 95mm Extended height: 196mm Lifting stroke: 101mm Weight of standard lever: 3.2kg Weight of insulated lever: 2.5kg Weight: 16.5kg

Hand-tools for PANLOCK and Elastic Spikes.

Hammers should NEVER be used for either insertion or extraction of PANLOCK.

Hammers may be used for the loosening of rusty PANLOCK, but NOT to fully extract.

Hammers can be used for the insertion of elastic spikes.

Available from Tool and Steel.

This tool is supplied with separate and detailed operating instructions.

Suitable for use on FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol VIPA-SP & SFC baseplates. Finally, because the reaction point for the installation tool has been moved to the head of the rail, the installer is able to lift sleepers (about 20mm) as part of the normal action of the tool, lifting from the rear arches of the clip before driving the clip into the installed position. NOTE: This tool has options avaialble under separate reference numbers; for variants with either insulated handles and / or cranked heads for confined spaces. The standard tool is always supplied with a straight head and steel handle. Optional variant of this tool using cranked head for confined spaces and insulated handle To insert the clips from the ‘Parked’ position of the shoulder as delivered from the sleeper factory, follow these instructions. The paddle should be in the normal front pivot hole and the side cheeks in the down position. (Different from the photograph) for ALL rail sizes. Locate the hooks on the side arms over the head of the rail. To insert the clips, grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip driving. Pull on the handle until refusal. The fully driven position for FASTCLIP ‘FC’ is achieved when the outer legs of the clip touch the rear of the side insulator in the shoulder, or with up to 3 mm of clearance. The FASTCLIP ‘FE’ installed position does NOT touch the shoulder or insulator. Once located the tool can be slid along the rail between sleepers for the next clip insertion. If the clip needs to be re-inserted from fully extracted, move the cheeks to the up position, to extend the reach of the tool. If more reach is required, the paddle can be moved to the rear pivot hole. Follow the instructions above.

• Magnetic Retrieving Baton with Release.
• Magnetic Retrieving Batons are innovative and powerful tools to remove ferrous materials in wet or dry environments.
• Non-corrosive, stainless steel.
• Use of safety goggles and gloves is highly recommended when using this item.
• Ideal for removing hardware from storage bins.
• Clean water or degreasing tanks of metal shavings.
• Unique shape allows for easy pick up from walls and corners.
• Constructed with neodymium/rare earth magnets to maximize holding power.
• Pull to release collected material to dispose of.

Light Weight "YELLOW" - Standard Strength PADS
The utilisation of new magnet material technology has enabled the dramatic reduction to the overall weight of the actual magnet unit, therefore developing a much more simplified track fixing procedure.
Single line attachment has been the key to significantly reducing the installation time, now approximately 30 seconds from stepping into the 4ft.
As stipulated by Network Rail each unit can be padlocked to deter vandals.