Catalogue No; Reference: 0039/42748 PANDROL No. LP1180. And for 4 shoulder baseplates. All STEL hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 32 mm diameter cylindrical straight handles, Instructions for PANPULLER LP1180 ​• Insert center leg of clip into housing. • Place pivoted hook over the inside of the front arch of clip with foot of PANPULLER behind clip housing and ensure lip of the hook is under the front arch. • Taking up a natural stance with feet apart, move one leg half a pace back to prevent loss of balance. Stand behind the PANPULLER, with both hands on tee handle at top of PANPULLER, pull strongly towards chest until refusal. • The PANPULLER automatically pulls clip to the correct position Extraction Instructions Reverse the PANPULLER • Taking up a natural stance (feet apart, move one leg half a pace back to prevent loss of balance) on the same side as for installation, place hook on the outside of the front arch of the clip, the foot of the PANPULLER resting on the baseplate/housing just above the centre leg of clip (as illustrated). • Standing behind PANPULLER with both hands on the tee handle at the top of PANPULLER, give a strong firm push away from your chest. • If clips have been in situ for many years, it may be necessary to use a hammer to loosen them taking safety precautions. If the clips will not move then use the Rusty Clip Extractor can be used for PR clips. NOTE. It is mandatory to wear eye protection when removing or fitting any clips where hammer assistance might be necessary.

The Vortok Fastclip Stressing Roller is designed to attach to the rail fastening, and by means of a rotating lift arm and bearing, contact the underside of the rail head and lift the rail from the sleeper (tie).
Once lifted, the rail can be moved with very low friction for the purposes of rail stressing, the resultant excellent stress distribution is therefore optimised.
The VSR can also be used for changing rail pads and the e-clip product has been designed with extra lift for that specific purpose.

EXTRACTOR, FASTCLIP FC, STEL, CREAM/GREEN 0039/047851 Fastclip Extraction Tool F41/G44/EG47 Cat No. 0039/047851 RB/BR/12 Suitable for all steel and concrete sleeper types. The extraction tool is used for side post insulator and clip/toe insulator replacement.

Cat No Reference: 0039/47852 Suitable for use on FASTCLIP FC and FASTCLIP FE The original version of the sleeper lifter can still be used in conjunction the new installer where sleepers need to be lifted more than 20mm. Instructions for Sleeper Lifter LP12608 The scissor action of the frame opens in order to locate the pincers of the tool into the sides of the shoulder with the clip in the ‘Parked’ position. Place the hook of the tool over the head of the rail, and as the body of the tool rises the scissor action closes the pincers and lock into the shoulder. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during sleeper lifting. Push the handle away to lift any ‘dropped’ sleeper if ballast conditions do not support the sleepers engaging with the foot of the rail. These tools should be used in pairs to lift the sleeper to locate both rails simultaneously with the rail seats of the sleeper. The sleeper lifter can used on the same rail seat as the FASTCLIP installer, by locating between the hooks of the installation tool.

Rear arch extractor for FASTCLIP ‘FC PANDROL No. LP15177 The rear arch extractor remains available to extract clips around IBJ’s. This tool is ONLY needed at IBJ’s in order to extract clips which are shielded by the scalloped section of the joint. It is also unique to FASTCLIP ‘FC’ and does NOT work with ‘FE’ clips. Instructions for Rear Arch Extractor The hooks in the frame of the tool locate into the reaction points on the shoulder, as shown in the photograph. The clip is extracted using the tines inserted in the rear arches of the clip. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip extraction. Push the handle away to extract the clip, stopping at the ‘Parked’ position, or continuing to push away to fully extract the clip from the shoulder.

Assorted car blade fuses, supplied in a transparent partitioned case.

Quantity: 120 blade fuses in total.

A useful assortment of popular, standard sized fuses used within the automotive industry.

Each handy partitioned container includes:

• 20 x 5 amp car blade fuses
• 20 x 10 amp car blade fuses
• 20 x 15 amp car blade fuses
• 20 x 20 amp car blade fuses
• 20 x 25 amp car blade fuses
• 20 x 30 amp car blade fuses

• Jerry Can Flexible Pouring Spout (Yellow)
• Optimum flow is assured when using our spouts with our cans
• Special breathing channel provide steady, glug-free pouring
• Each spout has an internal filter to protect charging tank from dirt and foreign bodies 
• Suitable for 5L, 10L and 20L Jerry Cans
• Includes an attachable clip for mounting the spout onto 10L and 20L Cans when not in use

Jerry Can Flexible Pouring Spout (Red)
Optimum flow is assured when using our spouts with our cans
Special breathing channel provide steady, glug-free pouring
Each spout has an internal filter to protect charging tank from dirt and foreign bodies
Suitable for 5L, 10L and 20L Jerry Cans
Includes an attachable clip for mounting the spout onto 10L and 20L Cans when not in use

• Jerry Can Flexible Pouring Spout (Green)
• Optimum flow is assured when using our spouts with our cans
• Special breathing channel provide steady, glug-free pouring
• Each spout has an internal filter to protect charging tank from dirt and foreign bodies 
• Suitable for 5L, 10L and 20L Jerry Cans
• Includes an attachable clip for mounting the spout onto 10L and 20L Cans when not in use

• Jerry Can Flexible Pouring Spout (Black)
• Optimum flow is assured when using our spouts with our cans
• Special breathing channel provide steady, glug-free pouring
• Each spout has an internal filter to protect charging tank from dirt and foreign bodies 
• Suitable for 5L, 10L and 20L Jerry Cans
• Includes an attachable clip for mounting the spout onto 10L and 20L Cans when not in use