Just a few hand movements is all it takes to install the lawn mower blade made from high-grade steel in the LMO 18-33 Battery. With a cutting width of 33 cm it achieves neat cutting results.

For effortless manoeuvring in the garden: the lightweight and extremely manoeuvrable battery lawn mower LMO 18-33 Battery Set including battery and fast charger.

Suitable for use on FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol VIPA-SP & SFC baseplates. Finally, because the reaction point for the installation tool has been moved to the head of the rail, the installer is able to lift sleepers (about 20mm) as part of the normal action of the tool, lifting from the rear arches of the clip before driving the clip into the installed position. NOTE: This tool has options avaialble under separate reference numbers; for variants with either insulated handles and / or cranked heads for confined spaces. The standard tool is always supplied with a straight head and steel handle. Optional variant of this tool using cranked head for confined spaces and insulated handle To insert the clips from the ‘Parked’ position of the shoulder as delivered from the sleeper factory, follow these instructions. The paddle should be in the normal front pivot hole and the side cheeks in the down position. (Different from the photograph) for ALL rail sizes. Locate the hooks on the side arms over the head of the rail. To insert the clips, grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip driving. Pull on the handle until refusal. The fully driven position for FASTCLIP ‘FC’ is achieved when the outer legs of the clip touch the rear of the side insulator in the shoulder, or with up to 3 mm of clearance. The FASTCLIP ‘FE’ installed position does NOT touch the shoulder or insulator. Once located the tool can be slid along the rail between sleepers for the next clip insertion. If the clip needs to be re-inserted from fully extracted, move the cheeks to the up position, to extend the reach of the tool. If more reach is required, the paddle can be moved to the rear pivot hole. Follow the instructions above.

275 LUMEN SMD LED USB RECHARGABLE INSPECTION LIGHT WITH 250 LUMEN CREE TORCH IN TOP AND ROTATING MAGNETIC STAND - 3.7v 1600 mAh LI-ION INTEGRAL BATTERY - MICRO-USB CABLE (INC)

325 LUMEN COB LED INDUSTRIAL IK07 SENSOR HEADLIGHT - 3.7v 1500mAh LI-PO INTEGRAL BATTERY - MICRO-USB CABLE (INC)

275 LUMEN CREE LED USB RECHARGABLE HELMET MOUNTABLE HEADLIGHT WITH 2 x 5mm RED LEDs - 3.7v 1800mAh LI-POLYMER INTEGRAL BATTERY C/W DRAWSTRING STORAGE POUCH

RatGate is a non-return device that allows waste water to flow out of your home but helps preven rats from gaining entry.

• Easy to install - Only basic tools are required to install a RatGate
• Universal Fit - Available in 4" 110mm, 6" 160mm and 9" 225mm versions that it clay, plastic and cast iron drainage pipe
• Tough Construction - Made from high grade laser cut stainless steel
• Maintenance Free - Once the device is installed there is no maintenance required other than a periodic check
• Multi-Directional - Can be fitted in either the up or down stream direction of flow
• Accessible - The RatGate includes a liftable flap mechanism, providing easy access for drain maintenance
• Enviromentally Friendly - The device is humane, poison free and enviromentally friendly

WS3-10 Pacific Watersafe Cut Level 5 Glove

• Size 10
• Extra Large
• 13 gauge, green, Azura and polyester liner
• Dual latex coating
• Waterproof to the wrist
• Superb wet or dry suction grip
• Knit wrist