British Rail, Network Rail, Rail

SOCKET, IMPACT, BI-SQUARE, 1-1/8" X 1" DRIVE, AS CHAIR SCREW

50mm pin
500mm ring suits this socket

RatGate is a non-return device that allows waste water to flow out of your home but helps preven rats from gaining entry.

• Easy to install - Only basic tools are required to install a RatGate
• Universal Fit - Available in 4" 110mm, 6" 160mm and 9" 225mm versions that it clay, plastic and cast iron drainage pipe
• Tough Construction - Made from high grade laser cut stainless steel
• Maintenance Free - Once the device is installed there is no maintenance required other than a periodic check
• Multi-Directional - Can be fitted in either the up or down stream direction of flow
• Accessible - The RatGate includes a liftable flap mechanism, providing easy access for drain maintenance
• Enviromentally Friendly - The device is humane, poison free and enviromentally friendly

Catalogue No; Reference: 0039/42748 PANDROL No. LP1180. And for 4 shoulder baseplates. All STEL hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 32 mm diameter cylindrical straight handles, Instructions for PANPULLER LP1180 ​• Insert center leg of clip into housing. • Place pivoted hook over the inside of the front arch of clip with foot of PANPULLER behind clip housing and ensure lip of the hook is under the front arch. • Taking up a natural stance with feet apart, move one leg half a pace back to prevent loss of balance. Stand behind the PANPULLER, with both hands on tee handle at top of PANPULLER, pull strongly towards chest until refusal. • The PANPULLER automatically pulls clip to the correct position Extraction Instructions Reverse the PANPULLER • Taking up a natural stance (feet apart, move one leg half a pace back to prevent loss of balance) on the same side as for installation, place hook on the outside of the front arch of the clip, the foot of the PANPULLER resting on the baseplate/housing just above the centre leg of clip (as illustrated). • Standing behind PANPULLER with both hands on the tee handle at the top of PANPULLER, give a strong firm push away from your chest. • If clips have been in situ for many years, it may be necessary to use a hammer to loosen them taking safety precautions. If the clips will not move then use the Rusty Clip Extractor can be used for PR clips. NOTE. It is mandatory to wear eye protection when removing or fitting any clips where hammer assistance might be necessary.

Light Weight "YELLOW" - Standard Strength PADS
The utilisation of new magnet material technology has enabled the dramatic reduction to the overall weight of the actual magnet unit, therefore developing a much more simplified track fixing procedure.
Single line attachment has been the key to significantly reducing the installation time, now approximately 30 seconds from stepping into the 4ft.
As stipulated by Network Rail each unit can be padlocked to deter vandals.

The Vortok Fastclip Stressing Roller is designed to attach to the rail fastening, and by means of a rotating lift arm and bearing, contact the underside of the rail head and lift the rail from the sleeper (tie).
Once lifted, the rail can be moved with very low friction for the purposes of rail stressing, the resultant excellent stress distribution is therefore optimised.
The VSR can also be used for changing rail pads and the e-clip product has been designed with extra lift for that specific purpose.

The VSR is designed to attach to the rail fastening, and by means of a rotating lift arm and bearing, contact the underside of the rail head and lift the rail from the sleeper (tie).
Once lifted, the rail can be moved with very low friction for the purposes of rail stressing, the resultant excellent stress distribution is therefore optimised.
The VSR can also be used for changing rail pads and the e-clip product has been designed with extra lift for that specific purpose.

• Emergency Serviceable G Clamp
• Suitable for Common Rail Profiles
• 95RBS BH/97.1/2 BH, 109/BS110A/BS113A FB, CEN60 E1/E2

Short Pilot Pin

Used in conjunction with standard length rail cutters for hole centre location and when depressed allows coolant to reach the cutter and aids ejection of the "slug" when drilling is complete

• A Network Rail approved compact and lightweight Possession Limit Board with integral rail top clamp.
• Tilt Switch Operation - No keys to use or lose
• LED Light - Flashing Day and Night
• Powered by 2 No "C" cell batteries
• Weight - 2kg