This all steel grafting tool has a dished blade and a curved cutting edge which makes it ideal for clay digging and heavy ground breaking work.
It has a forged blade, tubular steel shaft and steel YD grip with wooden cross piece for added comfort.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE: 6" WIDE X 12" LONG

Suitable for use on FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol VIPA-SP & SFC baseplates. Finally, because the reaction point for the installation tool has been moved to the head of the rail, the installer is able to lift sleepers (about 20mm) as part of the normal action of the tool, lifting from the rear arches of the clip before driving the clip into the installed position. NOTE: This tool has options avaialble under separate reference numbers; for variants with either insulated handles and / or cranked heads for confined spaces. The standard tool is always supplied with a straight head and steel handle. Optional variant of this tool using cranked head for confined spaces and insulated handle To insert the clips from the ‘Parked’ position of the shoulder as delivered from the sleeper factory, follow these instructions. The paddle should be in the normal front pivot hole and the side cheeks in the down position. (Different from the photograph) for ALL rail sizes. Locate the hooks on the side arms over the head of the rail. To insert the clips, grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip driving. Pull on the handle until refusal. The fully driven position for FASTCLIP ‘FC’ is achieved when the outer legs of the clip touch the rear of the side insulator in the shoulder, or with up to 3 mm of clearance. The FASTCLIP ‘FE’ installed position does NOT touch the shoulder or insulator. Once located the tool can be slid along the rail between sleepers for the next clip insertion. If the clip needs to be re-inserted from fully extracted, move the cheeks to the up position, to extend the reach of the tool. If more reach is required, the paddle can be moved to the rear pivot hole. Follow the instructions above.

Fastclip Installation Tool F41/G44/EG47 Cat No. 0039/047850 RB/BR/123 Suitable for all steel and concrete sleeper types. The installation tool has two functions, each achieved by simply re-positioning a moveable pin. With the pin passing through the rear hole of the claw, installation of a Pandrol Fastclip assembly in the ‘switched off’ position is carried out. When the pin is re-positioned to the front hole of the claw and the installation operation repeated, the assembly will be in the ‘switched on’ position.

EXTRACTOR, FASTCLIP FC, STEL, CREAM/GREEN 0039/047851 Fastclip Extraction Tool F41/G44/EG47 Cat No. 0039/047851 RB/BR/12 Suitable for all steel and concrete sleeper types. The extraction tool is used for side post insulator and clip/toe insulator replacement.

Insulated 7lb Sledge Hammer
Insulated to BS8020

TONGS FOR NWR CONCRETE CROSSING BEARER URLT/023118 0039/068275

The LARGE-MAGNET is an ultra-robust steel and aluminium magnet to attach to a Unilite LED work light (SLR-1300, SLR-2500, SLR-2750, SLR-4750, SLR-4400, SLR-6000 & SP-4500). A secure locking wing nut is used to hold the site light securely in place.

Dimensions: 54mm W x 54mm L x 37mm H

Weight: 169g

Data Sheet

Hand-tools for PANLOCK and Elastic Spikes.

Hammers should NEVER be used for either insertion or extraction of PANLOCK.

Hammers may be used for the loosening of rusty PANLOCK, but NOT to fully extract.

Hammers can be used for the insertion of elastic spikes.

Available from Tool and Steel.

This tool is supplied with separate and detailed operating instructions.

The Karcher Xpert range are robust, reliable Karcher professional pressure washers specially designed for the rigours of trade & construction use.

The Xpert OneTen HD 7125 features tough components throughout, including a brass cylinder head & water inlet, 10m heavy duty wire-braided antikink hose & stainless steel pistoms & spray lance.

Thanks to its 1.4kW motor, the Xpert OneTen provides a max pressure output of 110 bar, enabling you to quickly & easily blast dirt away from the cleaning surface. The detergent intake hose also allows you to apply chemical through the machine, helping to remove any stubborn / ingrained dirt.

The Karcher Xpert range now features the EASY!Force tigger gun, giving you the power to use the high pressure output with ease.

The revolutionary operating concept of the EASY!Force trigger gun uses the recoil force of the high pressure jet & reduces the holding force for the trigger to zero, ensuring more effortless, ergonomic & stress-free use.

In addition the Xpert OneTen also features Karcher’s patented EASY!Lock quick locks, meaning connection is quick and easy, 5 times faster compared with conventional screw connections whilst remaining just as durable & robust. The Xpert OneTen will also feature a stainless steel spray lance, EASY!Force trigger gun & triple nozzle.