Hand-tools for PANLOCK and Elastic Spikes.

Hammers should NEVER be used for either insertion or extraction of PANLOCK.

Hammers may be used for the loosening of rusty PANLOCK, but NOT to fully extract.

Hammers can be used for the insertion of elastic spikes.

Available from Tool and Steel.

This tool is supplied with separate and detailed operating instructions.

The lawn mower blade with a cutting width of 36 cm is suitable for use in the battery-powered LMO 18-36 Battery, thus ensuring excellent cutting results.

Just a few hand movements is all it takes to install the lawn mower blade made from high-grade steel in the LMO 18-33 Battery. With a cutting width of 33 cm it achieves neat cutting results.

For effortless manoeuvring in the garden: the lightweight and extremely manoeuvrable battery lawn mower LMO 18-33 Battery Set including battery and fast charger.

Suitable for use on FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol VIPA-SP & SFC baseplates. Finally, because the reaction point for the installation tool has been moved to the head of the rail, the installer is able to lift sleepers (about 20mm) as part of the normal action of the tool, lifting from the rear arches of the clip before driving the clip into the installed position. NOTE: This tool has options avaialble under separate reference numbers; for variants with either insulated handles and / or cranked heads for confined spaces. The standard tool is always supplied with a straight head and steel handle. Optional variant of this tool using cranked head for confined spaces and insulated handle To insert the clips from the ‘Parked’ position of the shoulder as delivered from the sleeper factory, follow these instructions. The paddle should be in the normal front pivot hole and the side cheeks in the down position. (Different from the photograph) for ALL rail sizes. Locate the hooks on the side arms over the head of the rail. To insert the clips, grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip driving. Pull on the handle until refusal. The fully driven position for FASTCLIP ‘FC’ is achieved when the outer legs of the clip touch the rear of the side insulator in the shoulder, or with up to 3 mm of clearance. The FASTCLIP ‘FE’ installed position does NOT touch the shoulder or insulator. Once located the tool can be slid along the rail between sleepers for the next clip insertion. If the clip needs to be re-inserted from fully extracted, move the cheeks to the up position, to extend the reach of the tool. If more reach is required, the paddle can be moved to the rear pivot hole. Follow the instructions above.

Light Weight "YELLOW" - Standard Strength PADS
The utilisation of new magnet material technology has enabled the dramatic reduction to the overall weight of the actual magnet unit, therefore developing a much more simplified track fixing procedure.
Single line attachment has been the key to significantly reducing the installation time, now approximately 30 seconds from stepping into the 4ft.
As stipulated by Network Rail each unit can be padlocked to deter vandals.

• Heavy Duty Digging Bar
• Hardened Steel
• 1.7 Metre overall length 

• Graphite cast iron load sheave
• Hand lever made of malleable cast iron or tubular steel model with rubber grip
• Automatically acting load pressure brake
• Free chaining device optional
• Drop forged load and suspension hooks
• Asbestos-free friction discs

Yale Hand Lever Hoists are versatile, portable units for pulling, tensioning, lashing and lifting loads. The operation of the Hand Lever Hoists is easy and safe.
Light weight, robust malleable cast iron model, free chaining, slip clutch, stamped steel - or aluminium housing, low operating effort - in the Yale product range you will always find an optimal hoist for every type of operation.
The brake system of all Yale hand lever hoists are based on the original Yale patent of the British Engineer Thomas A Weston dating back to 1875. All parts of the load brake are made of high quality materials and are protected against corrosion.
The graphite cast iron load sheave for the link chain has precision machined chain pockets for accurate fit and durability of the load chain. The roller chain sprocket is made from heat treated chromium-molybdenum steel with precision machine teeth to ensure smooth chain movement.
Every Yale ratchet lever hoist is factory tested with overload. The units are supplied with a test certificate showing the serial-No. Operating instructions which contain an EC declaration of conformity are also attached to each unit.