This all steel grafting tool has a dished blade and a curved cutting edge which makes it ideal for clay digging and heavy ground breaking work.
It has a forged blade, tubular steel shaft and steel YD grip with wooden cross piece for added comfort.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE: 6" WIDE X 12" LONG

This all steel Newcastle draining shovel has a forged blade, tubular steel shaft and steel YD grip with wooden cross piece for added comfort.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE : 7" WIDE, TAPERING TO 4" BY 16" LONG

This all steel round mouth shovel has a forged blade, tubular steel shaft and steel YD grip with wooden cross piece for added comfort.

Used for excavating, digging and shovelling most aggregates. The pointed blade offers easier penetration in tougher ground.

PRODUCT HANDLE: 28"/ 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE: 10" WIDE X 12.1/2" LONG

This all steel rabbit shovel has a forged blade, tubular steel shaft and steel YD grip with wooden cross piece for added comfort.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: 7" TO 5"X 12"

Length 112cm
Width 15cm
Weight 2.5kg

All Steel Square Mouth Shovel intended for shoveling out, concrete mixing, working tarmac as well as cement, back filling trenches and maneuvering ballast.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE: 10'' WIDE X 12.1/2" LONG

Rear arch extractor for FASTCLIP ‘FC PANDROL No. LP15177 The rear arch extractor remains available to extract clips around IBJ’s. This tool is ONLY needed at IBJ’s in order to extract clips which are shielded by the scalloped section of the joint. It is also unique to FASTCLIP ‘FC’ and does NOT work with ‘FE’ clips. Instructions for Rear Arch Extractor The hooks in the frame of the tool locate into the reaction points on the shoulder, as shown in the photograph. The clip is extracted using the tines inserted in the rear arches of the clip. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip extraction. Push the handle away to extract the clip, stopping at the ‘Parked’ position, or continuing to push away to fully extract the clip from the shoulder.

Cat No Reference: 0039/47852 Suitable for use on FASTCLIP FC and FASTCLIP FE The original version of the sleeper lifter can still be used in conjunction the new installer where sleepers need to be lifted more than 20mm. Instructions for Sleeper Lifter LP12608 The scissor action of the frame opens in order to locate the pincers of the tool into the sides of the shoulder with the clip in the ‘Parked’ position. Place the hook of the tool over the head of the rail, and as the body of the tool rises the scissor action closes the pincers and lock into the shoulder. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during sleeper lifting. Push the handle away to lift any ‘dropped’ sleeper if ballast conditions do not support the sleepers engaging with the foot of the rail. These tools should be used in pairs to lift the sleeper to locate both rails simultaneously with the rail seats of the sleeper. The sleeper lifter can used on the same rail seat as the FASTCLIP installer, by locating between the hooks of the installation tool.

Cat No; Reference: 0039/42900 The PANSETTER is suitable for all Network Rail Sleepers fitted with PR, e & e-PLUS. Used for lifting the sleeper to the rail foot. It pushes the rail over, leaving the correct gap between the rail foot and the Pandrol housing, so that the insulator can be easily placed in the correct position. All Pandrol hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 35mm diameter cylindrical handles with ‘T’ cross bars for improved ergonomic and safer use.

15" Fishplate Nut Running Spanner, used for the quick release of fish plate nuts. The length of the handle allows the railway worker to quickly remove or tighten the nuts.

Taper Mouth Steel Ballast Shovel

Used for shovelling out or concrete mixing, working tarmac and cement, backfilling trenches and manouvering ballast.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE:10" WIDE, TAPERING TO 8.1/2" BY 12.1/2'' LONG