Mop Handle Green

EXTRACTOR, FASTCLIP FC, STEL, CREAM/GREEN 0039/047851 Fastclip Extraction Tool F41/G44/EG47 Cat No. 0039/047851 RB/BR/12 Suitable for all steel and concrete sleeper types. The extraction tool is used for side post insulator and clip/toe insulator replacement.

Fastclip Installation Tool F41/G44/EG47 Cat No. 0039/047850 RB/BR/123 Suitable for all steel and concrete sleeper types. The installation tool has two functions, each achieved by simply re-positioning a moveable pin. With the pin passing through the rear hole of the claw, installation of a Pandrol Fastclip assembly in the ‘switched off’ position is carried out. When the pin is re-positioned to the front hole of the claw and the installation operation repeated, the assembly will be in the ‘switched on’ position.

No. AE17256 formerly No. LP15923

Colour: White

The tool is used with the eP20129 green or eP20130 yellow e-PLUS clips, mostly with RT60 and NR60 S&C layouts.

INSULATED SLEDGE HAMMER 10LB

35" Overall Length

INSULATED HAMMER CLUB 2.5LB

10" Overall Length

Suitable for use on FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol VIPA-SP & SFC baseplates. Finally, because the reaction point for the installation tool has been moved to the head of the rail, the installer is able to lift sleepers (about 20mm) as part of the normal action of the tool, lifting from the rear arches of the clip before driving the clip into the installed position. NOTE: This tool has options avaialble under separate reference numbers; for variants with either insulated handles and / or cranked heads for confined spaces. The standard tool is always supplied with a straight head and steel handle. Optional variant of this tool using cranked head for confined spaces and insulated handle To insert the clips from the ‘Parked’ position of the shoulder as delivered from the sleeper factory, follow these instructions. The paddle should be in the normal front pivot hole and the side cheeks in the down position. (Different from the photograph) for ALL rail sizes. Locate the hooks on the side arms over the head of the rail. To insert the clips, grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip driving. Pull on the handle until refusal. The fully driven position for FASTCLIP ‘FC’ is achieved when the outer legs of the clip touch the rear of the side insulator in the shoulder, or with up to 3 mm of clearance. The FASTCLIP ‘FE’ installed position does NOT touch the shoulder or insulator. Once located the tool can be slid along the rail between sleepers for the next clip insertion. If the clip needs to be re-inserted from fully extracted, move the cheeks to the up position, to extend the reach of the tool. If more reach is required, the paddle can be moved to the rear pivot hole. Follow the instructions above.

Taper Mouth Steel Ballast Shovel

Used for shovelling out or concrete mixing, working tarmac and cement, backfilling trenches and manouvering ballast.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE:10" WIDE, TAPERING TO 8.1/2" BY 12.1/2'' LONG

Insulated Treaded Round Mouth Shovel Shovel

Treaded

Tested And Certified To BS8020:2011

Handle - 28" / 711mm Blade Size - 10" Wide By 12.1/2" Long

Tested For Live Work

Used for excavating, diggiing and sovelling most aggregates. The pointed blade offers easier penetration in tougher ground.

Mop Handle Red