• Insulated Heel & Point Crowbar
• 60" Insulated Solid, Non-Conductive Fibreglass Shaft with Forged Steel Ends
• Conforms to BS8020
• Quote MM0001 when ordering over the phone to receive our special price of £35 (exc vat)
• Tested up to 10000V
• Safe for up to 1000V 
• 1.5M 
• 6KG

Insulated 1.5M Point End Crowbar

• Insulated Point End Crowbar
• Insulated Solid Fibreglass Shaft
• Conforms to BS8020
• Rubber Grip for Extra Comfort
• 32MM Ø X 57" Long

Insulated Chisel End Crowbar

Insulated Heel End Crowbar

All Steel Square Mouth Shovel intended for shoveling out, concrete mixing, working tarmac as well as cement, back filling trenches and maneuvering ballast.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE: 10'' WIDE X 12.1/2" LONG

• Tongs used for the safe manual handling and moving of Steel Sleepers.
• Built to be both durable and robust, they allow the rail worker to use them to re-position and remove steel sleepers as required.
• Insulated to BS8020.

Rear arch extractor for FASTCLIP ‘FC PANDROL No. LP15177 The rear arch extractor remains available to extract clips around IBJ’s. This tool is ONLY needed at IBJ’s in order to extract clips which are shielded by the scalloped section of the joint. It is also unique to FASTCLIP ‘FC’ and does NOT work with ‘FE’ clips. Instructions for Rear Arch Extractor The hooks in the frame of the tool locate into the reaction points on the shoulder, as shown in the photograph. The clip is extracted using the tines inserted in the rear arches of the clip. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip extraction. Push the handle away to extract the clip, stopping at the ‘Parked’ position, or continuing to push away to fully extract the clip from the shoulder.

Cat No Reference: 0039/47852 Suitable for use on FASTCLIP FC and FASTCLIP FE The original version of the sleeper lifter can still be used in conjunction the new installer where sleepers need to be lifted more than 20mm. Instructions for Sleeper Lifter LP12608 The scissor action of the frame opens in order to locate the pincers of the tool into the sides of the shoulder with the clip in the ‘Parked’ position. Place the hook of the tool over the head of the rail, and as the body of the tool rises the scissor action closes the pincers and lock into the shoulder. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during sleeper lifting. Push the handle away to lift any ‘dropped’ sleeper if ballast conditions do not support the sleepers engaging with the foot of the rail. These tools should be used in pairs to lift the sleeper to locate both rails simultaneously with the rail seats of the sleeper. The sleeper lifter can used on the same rail seat as the FASTCLIP installer, by locating between the hooks of the installation tool.

EXTRACTOR, FASTCLIP FC, STEL, CREAM/GREEN 0039/047851 Fastclip Extraction Tool F41/G44/EG47 Cat No. 0039/047851 RB/BR/12 Suitable for all steel and concrete sleeper types. The extraction tool is used for side post insulator and clip/toe insulator replacement.

Fastclip Installation Tool F41/G44/EG47 Cat No. 0039/047850 RB/BR/123 Suitable for all steel and concrete sleeper types. The installation tool has two functions, each achieved by simply re-positioning a moveable pin. With the pin passing through the rear hole of the claw, installation of a Pandrol Fastclip assembly in the ‘switched off’ position is carried out. When the pin is re-positioned to the front hole of the claw and the installation operation repeated, the assembly will be in the ‘switched on’ position.