INSULATED SLEDGE HAMMER 10LB

35" Overall Length

INSULATED HAMMER CLUB 4LB

10" Overall Length

INSULATED HAMMER CLUB 2.5LB

10" Overall Length

Suitable for use on FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol VIPA-SP & SFC baseplates. Finally, because the reaction point for the installation tool has been moved to the head of the rail, the installer is able to lift sleepers (about 20mm) as part of the normal action of the tool, lifting from the rear arches of the clip before driving the clip into the installed position. NOTE: This tool has options avaialble under separate reference numbers; for variants with either insulated handles and / or cranked heads for confined spaces. The standard tool is always supplied with a straight head and steel handle. Optional variant of this tool using cranked head for confined spaces and insulated handle To insert the clips from the ‘Parked’ position of the shoulder as delivered from the sleeper factory, follow these instructions. The paddle should be in the normal front pivot hole and the side cheeks in the down position. (Different from the photograph) for ALL rail sizes. Locate the hooks on the side arms over the head of the rail. To insert the clips, grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip driving. Pull on the handle until refusal. The fully driven position for FASTCLIP ‘FC’ is achieved when the outer legs of the clip touch the rear of the side insulator in the shoulder, or with up to 3 mm of clearance. The FASTCLIP ‘FE’ installed position does NOT touch the shoulder or insulator. Once located the tool can be slid along the rail between sleepers for the next clip insertion. If the clip needs to be re-inserted from fully extracted, move the cheeks to the up position, to extend the reach of the tool. If more reach is required, the paddle can be moved to the rear pivot hole. Follow the instructions above.

Colour: Red working head (matches the appropriate e-PLUS clip type), and yellow handle. For use with eP20127 clips for retrofitting to sleeper types: F27, EF28, 5EF28, and for the new S&C designs to NR56V. All STEL hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 32mm diameter cylindrical straight handles Installation Instructions • Insert center leg of clip into housing. • Place pivoted hook over the inside of the front arch of clip with foot of PANPULLER behind clip housing and ensure lip of the hook is under the front arch. • Taking up a natural stance with feet apart, move one leg half a pace back to prevent loss of balance. Stand behind the PANPULLER, with both hands on tee handle at top of PANPULLER, pull strongly towards chest until refusal. • The PANPULLER automatically pulls clip to the correct position When correctly installed the centre leg of ALL types of e-PLUS clips, protrude beyond the shoulder to hold the side-insulator in the correct position. This tool is 'handed' to hold the insulator in position during clip insertion. This means that the tool cannot be used for extraction of the clip. To extract this e-Plus clip use a standard PANPULLER Type LP1180

Taper Mouth Steel Ballast Shovel

Used for shovelling out or concrete mixing, working tarmac and cement, backfilling trenches and manouvering ballast.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE:10" WIDE, TAPERING TO 8.1/2" BY 12.1/2'' LONG

Insulated Treaded Round Mouth Shovel Shovel

Treaded

Tested And Certified To BS8020:2011

Handle - 28" / 711mm Blade Size - 10" Wide By 12.1/2" Long

Tested For Live Work

Used for excavating, diggiing and sovelling most aggregates. The pointed blade offers easier penetration in tougher ground.

Mop Handle Green

Mop Handle Red

Mop Handle Blue

Catalogue No; Reference: 0039/42748 PANDROL No. LP1180. And for 4 shoulder baseplates. All STEL hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 32 mm diameter cylindrical straight handles, Instructions for PANPULLER LP1180 ​• Insert center leg of clip into housing. • Place pivoted hook over the inside of the front arch of clip with foot of PANPULLER behind clip housing and ensure lip of the hook is under the front arch. • Taking up a natural stance with feet apart, move one leg half a pace back to prevent loss of balance. Stand behind the PANPULLER, with both hands on tee handle at top of PANPULLER, pull strongly towards chest until refusal. • The PANPULLER automatically pulls clip to the correct position Extraction Instructions Reverse the PANPULLER • Taking up a natural stance (feet apart, move one leg half a pace back to prevent loss of balance) on the same side as for installation, place hook on the outside of the front arch of the clip, the foot of the PANPULLER resting on the baseplate/housing just above the centre leg of clip (as illustrated). • Standing behind PANPULLER with both hands on the tee handle at the top of PANPULLER, give a strong firm push away from your chest. • If clips have been in situ for many years, it may be necessary to use a hammer to loosen them taking safety precautions. If the clips will not move then use the Rusty Clip Extractor can be used for PR clips. NOTE. It is mandatory to wear eye protection when removing or fitting any clips where hammer assistance might be necessary.

• Magnetic Retrieving Baton with Release.
• Magnetic Retrieving Batons are innovative and powerful tools to remove ferrous materials in wet or dry environments.
• Non-corrosive, stainless steel.
• Use of safety goggles and gloves is highly recommended when using this item.
• Ideal for removing hardware from storage bins.
• Clean water or degreasing tanks of metal shavings.
• Unique shape allows for easy pick up from walls and corners.
• Constructed with neodymium/rare earth magnets to maximize holding power.
• Pull to release collected material to dispose of.

• Emergency Serviceable G Clamp
• Suitable for Common Rail Profiles
• 95RBS BH/97.1/2 BH, 109/BS110A/BS113A FB, CEN60 E1/E2

Insulated Check Rail Spanner - 1-11/16" AF x 30" L
Insulated to BS8020

• Keying Hammer Head - 10lb / 4.5kg
• Hickory Handle
• Overall Length - Approximately 91.5cm

• Conforms to BS8020 : 2011
• Keying Hammer Head - 10lb / 4.5kg
• Fiberglass Shaft
• Rubber Grip Handle
• Steel Protective Collar
• Overall Length - Approximately 92.5cm

• Sledge Hammer Head - 10lb / 4.5kg
• Hickory Handle
• Overall Length - Approximately 75cm

• Conforms to BS8020
• Certified to 1000 Volts - Tested to 10000 Volts
• Solid forged from one piece of steel
• YD handle
• Strong yet lightweight fibreglass shaft has excellent insulating properties
• Lightweight at just 2.5kg
• BS8020:2011

Cat No; Reference: 0039/42900 The PANSETTER is suitable for all Network Rail Sleepers fitted with PR, e & e-PLUS. Used for lifting the sleeper to the rail foot. It pushes the rail over, leaving the correct gap between the rail foot and the Pandrol housing, so that the insulator can be easily placed in the correct position. All Pandrol hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 35mm diameter cylindrical handles with ‘T’ cross bars for improved ergonomic and safer use.

It is recommended for safety reasons that contractors should formally check and record the wear of the hooks at intervals of 6 months using the wear gauge.
The gauge is suitable for all types of Panpuller or e-Plus Panpuller.
The wear gauge provides easy Go/No-Go assessment of when to replace the hook.
Work hooks have a tendency to slip off the clips, which can present a significant risk to operators.

Cat No Reference: 0039/47852 Suitable for use on FASTCLIP FC and FASTCLIP FE The original version of the sleeper lifter can still be used in conjunction the new installer where sleepers need to be lifted more than 20mm. Instructions for Sleeper Lifter LP12608 The scissor action of the frame opens in order to locate the pincers of the tool into the sides of the shoulder with the clip in the ‘Parked’ position. Place the hook of the tool over the head of the rail, and as the body of the tool rises the scissor action closes the pincers and lock into the shoulder. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during sleeper lifting. Push the handle away to lift any ‘dropped’ sleeper if ballast conditions do not support the sleepers engaging with the foot of the rail. These tools should be used in pairs to lift the sleeper to locate both rails simultaneously with the rail seats of the sleeper. The sleeper lifter can used on the same rail seat as the FASTCLIP installer, by locating between the hooks of the installation tool.

All Steel Square Mouth Shovel intended for shoveling out, concrete mixing, working tarmac as well as cement, back filling trenches and maneuvering ballast.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE: 10'' WIDE X 12.1/2" LONG

• Insulated Heel & Point Crowbar
• 60" Insulated Solid, Non-Conductive Fibreglass Shaft with Forged Steel Ends
• Conforms to BS8020
• Quote MM0001 when ordering over the phone to receive our special price of £35 (exc vat)
• Tested up to 10000V
• Safe for up to 1000V 
• 1.5M 
• 6KG

Insulated Chisel & Point Crowbar/Digging Bar

A durable, insulated wheelbarrow fabricated from a rugged single mould polyethylene material ideal for use on rail possessions and also utilities. 

• The STEL Insulated Wheelbarrow has a puncture proof tyre, also a double skin with 6mm walls made of Polyethylene to ensure maximum durability.
• No metal core parts are used resulting in the insulated wheelbarrow being a safer option for use in areas where conductivity may be an issue.
• The STEL insulated wheelbarrow is commonly used on or around 3rd rail / conductor rail working environments for safer working within possession zones.
• The STEL insulated wheelbarrow is also used for the application of cable laying.
• Our insulated wheelbarrow is robust with re-enforced handles and an extra strong tipping bar located in front of the wheel.
• Designed for the outside, the insulated wheelbarrow is rust free with a one piece mould construction resulting in fewer stress points.

• Capacity:      90L / 20 Gallon (Approx)
• Weight:        12kg (Empty)
• Dimensions: Length: 1540 x Width: 615 x Height: 620mm

Require more than one unit? Please call or email our sales office to request a quotation with respect to a multiple purchase discount.

Enquire today - Tel: 0114 383 0110 or email: sales@specialisedtools.co.uk

This all steel round mouth shovel has a forged blade, tubular steel shaft and steel YD grip with wooden cross piece for added comfort.

Used for excavating, digging and shovelling most aggregates. The pointed blade offers easier penetration in tougher ground.

PRODUCT HANDLE: 28"/ 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE: 10" WIDE X 12.1/2" LONG

Insulated Taper Mouth Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 10" Wide By 8.1/2" Tapering To 12.1/2" Long

Tested For Live Work Used for shovelling out or concrete mixing, working tarmac and cement, backfilling trenches and manouvering ballast.

Insulated Square Mouth Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 8" Wide By 10.1/2" Long

Tested For Live Work Used for shovelling out or concrete mixing, working tarmac and cement, backfilling trenches and manouvering ballast.