PANDROL No. LP7632 Especially for e2001 and e2007clips but NOT for 4-shoulder baseplates. NOTE hook positions for max efficiency: Upper pivot: Clip installation Lower pivot: Clip extraction All Pandrol hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 35mm diameter cylindrical handles with ‘T’ cross bars for improved ergonomic and safer use. Installation Instructions ​• Insert center leg of clip into housing. • Place pivoted hook over the inside of the front arch of clip with foot of PANPULLER behind clip housing and ensure lip of the hook is under the front arch. • Taking up a natural stance with feet apart, move one leg half a pace back to prevent loss of balance. Stand behind the PANPULLER, with both hands on tee handle at top of PANPULLER, pull strongly towards chest until refusal. • The PANPULLER automatically pulls clip to the correct position Extraction Instructions Reverse the PANPULLER

Product Code: 0039/047851 Previously LP18679 Suitable for extracting FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol baseplate types VIPA-SP & SFC baseplate. Instructions for Extractor AE17385 The Extractor tool acts as a lever against the web of the rail and the toe of the clip. To locate the tool hold at angle away from the rail and move forwards to position the tool between the rail and the shoulder, with the rear clip catching frame towards the operators foot. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip extraction. Push the handles away until the rear of the clip touches the catching frame, to ensure the clip remains in the shoulder, to locate in the ‘Parked’ position. Care should be taken to maintain the operator’s balance during clip extraction as the handle is pushed away. To remove the clip completely from the shoulder, keep pushing the handle so the frame hinges upwards and the clip is removed from the shoulder.

A Network Rail approved compact marker board, to denote a work site within a possession. PADS No; 0020/039499 Powered by 2No “C” cell batteries. Automatic On/Off operation—No keys to use or loose! Size 400mm x 240mm Complies with NWR Group Standard GIRT/7033 Issue 2 Supplied with batteries

Ergonomic temple for comfort fit.

• Temple tip locking catch.
• Temple ratchet adjustment.
• Hard coated polycarbonate lens.
• Anti-fog and anti-scratch.
• Soft nose pad.

Ergonomic temple provides comfortable, self-adjusting and a more secure fit to the users head. The swaying ergo temple pieces will spread the pressure evenly across the users temple area.

Temple ratchet adjustment works closely with the ergo temple to help the user wearing the product with different pantoscopic angles, suitable for all head shapes.

• Conform to EN166:
• Optical Class:1
• F T - (Low impact energy at extreme temperatures)
• 2C-1.2 - UV Filter
• K - Scratch Resistant
• N - Fog Resistant

Suitable for use on FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol VIPA-SP & SFC baseplates. Finally, because the reaction point for the installation tool has been moved to the head of the rail, the installer is able to lift sleepers (about 20mm) as part of the normal action of the tool, lifting from the rear arches of the clip before driving the clip into the installed position. NOTE: This tool has options avaialble under separate reference numbers; for variants with either insulated handles and / or cranked heads for confined spaces. The standard tool is always supplied with a straight head and steel handle. Optional variant of this tool using cranked head for confined spaces and insulated handle To insert the clips from the ‘Parked’ position of the shoulder as delivered from the sleeper factory, follow these instructions. The paddle should be in the normal front pivot hole and the side cheeks in the down position. (Different from the photograph) for ALL rail sizes. Locate the hooks on the side arms over the head of the rail. To insert the clips, grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip driving. Pull on the handle until refusal. The fully driven position for FASTCLIP ‘FC’ is achieved when the outer legs of the clip touch the rear of the side insulator in the shoulder, or with up to 3 mm of clearance. The FASTCLIP ‘FE’ installed position does NOT touch the shoulder or insulator. Once located the tool can be slid along the rail between sleepers for the next clip insertion. If the clip needs to be re-inserted from fully extracted, move the cheeks to the up position, to extend the reach of the tool. If more reach is required, the paddle can be moved to the rear pivot hole. Follow the instructions above.

Catalogue No; Reference: 0039/42748 PANDROL No. LP1180. And for 4 shoulder baseplates. All STEL hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 32 mm diameter cylindrical straight handles, Instructions for PANPULLER LP1180 ​• Insert center leg of clip into housing. • Place pivoted hook over the inside of the front arch of clip with foot of PANPULLER behind clip housing and ensure lip of the hook is under the front arch. • Taking up a natural stance with feet apart, move one leg half a pace back to prevent loss of balance. Stand behind the PANPULLER, with both hands on tee handle at top of PANPULLER, pull strongly towards chest until refusal. • The PANPULLER automatically pulls clip to the correct position Extraction Instructions Reverse the PANPULLER • Taking up a natural stance (feet apart, move one leg half a pace back to prevent loss of balance) on the same side as for installation, place hook on the outside of the front arch of the clip, the foot of the PANPULLER resting on the baseplate/housing just above the centre leg of clip (as illustrated). • Standing behind PANPULLER with both hands on the tee handle at the top of PANPULLER, give a strong firm push away from your chest. • If clips have been in situ for many years, it may be necessary to use a hammer to loosen them taking safety precautions. If the clips will not move then use the Rusty Clip Extractor can be used for PR clips. NOTE. It is mandatory to wear eye protection when removing or fitting any clips where hammer assistance might be necessary.

• Fuel and Fume Free Creating An Eco Friendly Drilling System
• Supplied With A Robust Carry Case, 59 Minute Fast Charger, Jigs, Pump Bottle, 2 x M18 Volt Fuel 9Ah Milwaukee Li-ion Batteries as Standard, LED Battery Status Indicators (optional in car charger available)
• Low Vibration (1.69 m/s2)
• Low Noise Level (82.5 dBA)
• Light Weight; 16.6Kg Including Battery and Handle
• Tool Free Detachable Handle for Left or Right Hand Operation
• Quick Tool Free Cutter Change
• Ergonomically Friendly Slim Profile For Easy Carrying
• Compatible With Most Popular Rail Shoes / Templates
• Brand - Steltools.co.uk

Light Weight "YELLOW" - Standard Strength PADS
The utilisation of new magnet material technology has enabled the dramatic reduction to the overall weight of the actual magnet unit, therefore developing a much more simplified track fixing procedure.
Single line attachment has been the key to significantly reducing the installation time, now approximately 30 seconds from stepping into the 4ft.
As stipulated by Network Rail each unit can be padlocked to deter vandals.

The Vortok Fastclip Stressing Roller is designed to attach to the rail fastening, and by means of a rotating lift arm and bearing, contact the underside of the rail head and lift the rail from the sleeper (tie).
Once lifted, the rail can be moved with very low friction for the purposes of rail stressing, the resultant excellent stress distribution is therefore optimised.
The VSR can also be used for changing rail pads and the e-clip product has been designed with extra lift for that specific purpose.

The VSR is designed to attach to the rail fastening, and by means of a rotating lift arm and bearing, contact the underside of the rail head and lift the rail from the sleeper (tie).
Once lifted, the rail can be moved with very low friction for the purposes of rail stressing, the resultant excellent stress distribution is therefore optimised.
The VSR can also be used for changing rail pads and the e-clip product has been designed with extra lift for that specific purpose.