THINSULATED HAT BEANIE STYLE BLACK HAT

INSULATED HAMMER CLUB 2.5LB

10" Overall Length

INSULATED HAMMER CLUB 4LB

10" Overall Length

INSULATED SLEDGE HAMMER 7LB

35" Overall Length

INSULATED SLEDGE HAMMER 10LB

35" Overall Length

Insulated Taper Mouth Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 10" Wide By 8.1/2" Tapering To 12.1/2" Long

Tested For Live Work Used for shovelling out or concrete mixing, working tarmac and cement, backfilling trenches and manouvering ballast.

Insulated Trenching Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 7" Wide x 11" Long

Tested For Live Work Often known as a '2-way' in some trades Used for digging and cleaning out narrow trenches for cable and pipe laying

Insulated Cable Laying Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 5" Wide Tapering to 4.1/2" By 11"

Long Tested For Live Work Often known as a '1-way' in some trades.

Designed for cable and pipe laying with a slim blade that is ideal for digging out narrow trenches.

Insulated Rabbit Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 7-1/2" Wide By x 11-1/2"

Tested For Live Work Ideal For Transplanting Plants And Shrubs And Also For Post-Holing Jobs

Insulated Treaded Round Mouth Shovel Shovel

Treaded

Tested And Certified To BS8020:2011

Handle - 28" / 711mm Blade Size - 10" Wide By 12.1/2" Long

Tested For Live Work

Used for excavating, diggiing and sovelling most aggregates. The pointed blade offers easier penetration in tougher ground.

Insulated Square Mouth Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 8" Wide By 10.1/2" Long

Tested For Live Work Used for shovelling out or concrete mixing, working tarmac and cement, backfilling trenches and manouvering ballast.

Insulated Newcastle Treaded Shovel

Tested And Certified To BS8020:2011

Treaded Tested For Live Work 16" Long, 7" Wide Tapering to 4"

Often known as a 'grafter' in some trades.

Designed for digging deep and narrow trenches, channels and post holes.

Insulated Clay Grafting Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 6" Wide By 12" Long T

ested For Live Work With a slightly dished blade and round cutting edge, designed for clay digging and heavy ground breaking.

BS8020 Insulated Fibreglass Pick Shaft. Pultruded fibreglass core with an injection moulded polypropylene outer. BS Standard 3'' x 2'' eye. Tested and made in conformance with BS8020:2011. Tools for live working. This shaft is designed to be a tap on fit, however when fitting a replacement shaft, the eye should be dressed to suit the hammer head by a competent person.

• Conforms to BS8020
• Certified to 1000 Volts - Tested to 10000 Volts
• Solid forged from one piece of steel
• YD handle
• Strong yet lightweight fibreglass shaft has excellent insulating properties
• Lightweight at just 2.5kg
• BS8020:2011

Insulated Chisel & Point Crowbar/Digging Bar

• Insulated Heel & Point Crowbar
• 60" Insulated Solid, Non-Conductive Fibreglass Shaft with Forged Steel Ends
• Conforms to BS8020
• Quote MM0001 when ordering over the phone to receive our special price of £35 (exc vat)
• Tested up to 10000V
• Safe for up to 1000V 
• 1.5M 
• 6KG

SHOVEL, RABBIT / POST HOLE INSULATED HEAD SIZE 5-1/2" X 12" LONG 54" HANDLE, OVERALL LENGTH 72"

Insulated Chisel End Crowbar

Insulated Heel End Crowbar

Insulated 1.5M Point End Crowbar

• Insulated Point End Crowbar
• Insulated Solid Fibreglass Shaft
• Conforms to BS8020
• Rubber Grip for Extra Comfort
• 32MM Ø X 57" Long

SUMO, BUILDERS / FENCING INSULATED SPADE 54" LONG HANDLE, OVERALL LENGTH 72" HEAD SIZE 5-1/2" X 14" LONG

CABLE GUIDANCE TOOL, 37", INSULATED, USED IN CONJUNCTION WITH TROUGH LID LIFTER

JACK HANDLE, INSULATED DUFF NORTON TRIP 117A

Insulated Post Hole Digger Shovel Holder

46" HANDLE 

68" OVERALL LENGTH

• Conforms to BS8020
• Certified to 1000 Volts - Tested to 10000 Volts
• Solid forged from one piece of steel
• YD handle
• Strong yet lightweight fibreglass shaft has excellent insulating properties

Insulated 7lb Sledge Hammer
Insulated to BS8020

Rail Turning Bar - Insulated Bull Head
Insulated to BS8020

Insulated Keying Hammer - 7lb
Insulated to BS8020

• Insulated Pot Dolly Hexagon 17mm For Concrete

Insulated Simplex A17 Jack Handle
Insulated to BS8020

Insulated Hook Switch Pole
Insulated to BS8020

• Conforms to BS8020 : 2011
• Keying Hammer Head - 10lb / 4.5kg
• Fiberglass Shaft
• Rubber Grip Handle
• Steel Protective Collar
• Overall Length - Approximately 92.5cm

1 11/16" Bi-Square Fishplate Nut Spanner
36" BS8020 Fibreglass Insulated Shaft

Insulated Ferrule Extractor

Insulated Check Rail Spanner - 1-11/16" AF x 30" L
Insulated to BS8020

Cat No; Reference: 0039/42900 The PANSETTER is suitable for all Network Rail Sleepers fitted with PR, e & e-PLUS. Used for lifting the sleeper to the rail foot. It pushes the rail over, leaving the correct gap between the rail foot and the Pandrol housing, so that the insulator can be easily placed in the correct position. All Pandrol hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 35mm diameter cylindrical handles with ‘T’ cross bars for improved ergonomic and safer use.

A durable, insulated wheelbarrow fabricated from a rugged single mould polyethylene material ideal for use on rail possessions and also utilities. 

• The STEL Insulated Wheelbarrow has a puncture proof tyre, also a double skin with 6mm walls made of Polyethylene to ensure maximum durability.
• No metal core parts are used resulting in the insulated wheelbarrow being a safer option for use in areas where conductivity may be an issue.
• The STEL insulated wheelbarrow is commonly used on or around 3rd rail / conductor rail working environments for safer working within possession zones.
• The STEL insulated wheelbarrow is also used for the application of cable laying.
• Our insulated wheelbarrow is robust with re-enforced handles and an extra strong tipping bar located in front of the wheel.
• Designed for the outside, the insulated wheelbarrow is rust free with a one piece mould construction resulting in fewer stress points.

• Capacity:      90L / 20 Gallon (Approx)
• Weight:        12kg (Empty)
• Dimensions: Length: 1540 x Width: 615 x Height: 620mm

Require more than one unit? Please call or email our sales office to request a quotation with respect to a multiple purchase discount.

Enquire today - Tel: 0114 383 0110 or email: sales@specialisedtools.co.uk

The Vortok Fastclip Stressing Roller is designed to attach to the rail fastening, and by means of a rotating lift arm and bearing, contact the underside of the rail head and lift the rail from the sleeper (tie).
Once lifted, the rail can be moved with very low friction for the purposes of rail stressing, the resultant excellent stress distribution is therefore optimised.
The VSR can also be used for changing rail pads and the e-clip product has been designed with extra lift for that specific purpose.

Catalogue No; Reference: 0039/42748 PANDROL No. LP1180. And for 4 shoulder baseplates. All STEL hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 32 mm diameter cylindrical straight handles, Instructions for PANPULLER LP1180 ​• Insert center leg of clip into housing. • Place pivoted hook over the inside of the front arch of clip with foot of PANPULLER behind clip housing and ensure lip of the hook is under the front arch. • Taking up a natural stance with feet apart, move one leg half a pace back to prevent loss of balance. Stand behind the PANPULLER, with both hands on tee handle at top of PANPULLER, pull strongly towards chest until refusal. • The PANPULLER automatically pulls clip to the correct position Extraction Instructions Reverse the PANPULLER • Taking up a natural stance (feet apart, move one leg half a pace back to prevent loss of balance) on the same side as for installation, place hook on the outside of the front arch of the clip, the foot of the PANPULLER resting on the baseplate/housing just above the centre leg of clip (as illustrated). • Standing behind PANPULLER with both hands on the tee handle at the top of PANPULLER, give a strong firm push away from your chest. • If clips have been in situ for many years, it may be necessary to use a hammer to loosen them taking safety precautions. If the clips will not move then use the Rusty Clip Extractor can be used for PR clips. NOTE. It is mandatory to wear eye protection when removing or fitting any clips where hammer assistance might be necessary.

• Tongs used for the safe manual handling and moving of Steel Sleepers.
• Built to be both durable and robust, they allow the rail worker to use them to re-position and remove steel sleepers as required.
• Insulated to BS8020.

INSULATED TROUGH LID LIFTER / TILTER, ADJUSTABLE

Insulated Type E Clip Pan Setter

Cat No Reference: 0039/47852 Suitable for use on FASTCLIP FC and FASTCLIP FE The original version of the sleeper lifter can still be used in conjunction the new installer where sleepers need to be lifted more than 20mm. Instructions for Sleeper Lifter LP12608 The scissor action of the frame opens in order to locate the pincers of the tool into the sides of the shoulder with the clip in the ‘Parked’ position. Place the hook of the tool over the head of the rail, and as the body of the tool rises the scissor action closes the pincers and lock into the shoulder. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during sleeper lifting. Push the handle away to lift any ‘dropped’ sleeper if ballast conditions do not support the sleepers engaging with the foot of the rail. These tools should be used in pairs to lift the sleeper to locate both rails simultaneously with the rail seats of the sleeper. The sleeper lifter can used on the same rail seat as the FASTCLIP installer, by locating between the hooks of the installation tool.

Insulated Type E Clip & PR Clip Pan Puller

INSTALLER, FASTCLIP FC, STEL VIPA-SP, SFC YELLOW / GREEN 0039/047850

EXTRACTOR, FASTCLIP FC, STEL, CREAM/GREEN 0039/047851

TYPE FAST CLIP FC EXTRACTOR - FRANCE TYPE FASTCLIP FC OUTIL MANUEL D'EXTRACTION

Colour: Red working head (matches the appropriate e-PLUS clip type), and yellow handle. For use with eP20127 clips for retrofitting to sleeper types: F27, EF28, 5EF28, and for the new S&C designs to NR56V. All STEL hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 32mm diameter cylindrical straight handles Installation Instructions • Insert center leg of clip into housing. • Place pivoted hook over the inside of the front arch of clip with foot of PANPULLER behind clip housing and ensure lip of the hook is under the front arch. • Taking up a natural stance with feet apart, move one leg half a pace back to prevent loss of balance. Stand behind the PANPULLER, with both hands on tee handle at top of PANPULLER, pull strongly towards chest until refusal. • The PANPULLER automatically pulls clip to the correct position When correctly installed the centre leg of ALL types of e-PLUS clips, protrude beyond the shoulder to hold the side-insulator in the correct position. This tool is 'handed' to hold the insulator in position during clip insertion. This means that the tool cannot be used for extraction of the clip. To extract this e-Plus clip use a standard PANPULLER Type LP1180

Suitable for use on FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol VIPA-SP & SFC baseplates. Finally, because the reaction point for the installation tool has been moved to the head of the rail, the installer is able to lift sleepers (about 20mm) as part of the normal action of the tool, lifting from the rear arches of the clip before driving the clip into the installed position. NOTE: This tool has options avaialble under separate reference numbers; for variants with either insulated handles and / or cranked heads for confined spaces. The standard tool is always supplied with a straight head and steel handle. Optional variant of this tool using cranked head for confined spaces and insulated handle To insert the clips from the ‘Parked’ position of the shoulder as delivered from the sleeper factory, follow these instructions. The paddle should be in the normal front pivot hole and the side cheeks in the down position. (Different from the photograph) for ALL rail sizes. Locate the hooks on the side arms over the head of the rail. To insert the clips, grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip driving. Pull on the handle until refusal. The fully driven position for FASTCLIP ‘FC’ is achieved when the outer legs of the clip touch the rear of the side insulator in the shoulder, or with up to 3 mm of clearance. The FASTCLIP ‘FE’ installed position does NOT touch the shoulder or insulator. Once located the tool can be slid along the rail between sleepers for the next clip insertion. If the clip needs to be re-inserted from fully extracted, move the cheeks to the up position, to extend the reach of the tool. If more reach is required, the paddle can be moved to the rear pivot hole. Follow the instructions above.

Designed to be used singularly or in pairs, for the lifting and transportation of lengths or rail, or parts of points and crossings from one location to another. The Ironman can also be used to transpose rail from one side of the track to the other. Therefore by straddling the running rails, access to the four-foot, six-foot and cess is possible.