Wonder Wipes Multi-Use, formulated to clean hands, tools and surfaces from wet and semi-cured paint, sealant, adhesive, bitumen, expanding foam, oil, grease and even silicone

6 PACKS

All Steel Square Mouth Shovel intended for shoveling out, concrete mixing, working tarmac as well as cement, back filling trenches and maneuvering ballast.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE: 10'' WIDE X 12.1/2" LONG

Assorted car blade fuses, supplied in a transparent partitioned case.

Quantity: 120 blade fuses in total.

A useful assortment of popular, standard sized fuses used within the automotive industry.

Each handy partitioned container includes:

• 20 x 5 amp car blade fuses
• 20 x 10 amp car blade fuses
• 20 x 15 amp car blade fuses
• 20 x 20 amp car blade fuses
• 20 x 25 amp car blade fuses
• 20 x 30 amp car blade fuses

• Tongs used for the safe manual handling and moving of Steel Sleepers.
• Built to be both durable and robust, they allow the rail worker to use them to re-position and remove steel sleepers as required.

• Tongs used for the safe manual handling and moving of Steel Sleepers.
• Built to be both durable and robust, they allow the rail worker to use them to re-position and remove steel sleepers as required.
• Insulated to BS8020.

• Timber Nips used for the safe manual handling and movement of Timber Sleepers.
• A durable and robust tool

Rear arch extractor for FASTCLIP ‘FC PANDROL No. LP15177 The rear arch extractor remains available to extract clips around IBJ’s. This tool is ONLY needed at IBJ’s in order to extract clips which are shielded by the scalloped section of the joint. It is also unique to FASTCLIP ‘FC’ and does NOT work with ‘FE’ clips. Instructions for Rear Arch Extractor The hooks in the frame of the tool locate into the reaction points on the shoulder, as shown in the photograph. The clip is extracted using the tines inserted in the rear arches of the clip. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip extraction. Push the handle away to extract the clip, stopping at the ‘Parked’ position, or continuing to push away to fully extract the clip from the shoulder.

Cat No Reference: 0039/47852 Suitable for use on FASTCLIP FC and FASTCLIP FE The original version of the sleeper lifter can still be used in conjunction the new installer where sleepers need to be lifted more than 20mm. Instructions for Sleeper Lifter LP12608 The scissor action of the frame opens in order to locate the pincers of the tool into the sides of the shoulder with the clip in the ‘Parked’ position. Place the hook of the tool over the head of the rail, and as the body of the tool rises the scissor action closes the pincers and lock into the shoulder. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during sleeper lifting. Push the handle away to lift any ‘dropped’ sleeper if ballast conditions do not support the sleepers engaging with the foot of the rail. These tools should be used in pairs to lift the sleeper to locate both rails simultaneously with the rail seats of the sleeper. The sleeper lifter can used on the same rail seat as the FASTCLIP installer, by locating between the hooks of the installation tool.

• Conforms to BS8020
• Certified to 1000 Volts - Tested to 10000 Volts
• Solid forged from one piece of steel
• YD handle
• Strong yet lightweight fibreglass shaft has excellent insulating properties
• Lightweight at just 2.5kg
• BS8020:2011

• Conforms to BS8020
• Certified to 1000 Volts - Tested to 10000 Volts
• Solid forged from one piece of steel
• YD handle
• Strong yet lightweight fibreglass shaft has excellent insulating properties