Please Call For Parts List 0114 383 0110 or Email sales@specialisedtools.co.uk 

OUTPUT: 3.4kVA / 2.7kW
SOCKETS: 1 x 16a 115v / 1 x 32a 115v / 2 x 16a 230v
ENGINE: Honda GX200
HP/CYLINDERS: 6.5 / 1
START: Recoil
FUEL TANK: 3.1 Litres
RUN TIME: 2.5 Hours
NOISE LEVEL: 71dBA @ 7 metres
DIMENSIONS: L610 x W420 x H415mm
WEIGHT: 36 KG
OPTIONS: Single voltage, LPG conversion, Long run tank (metal), Trolley kit.

Suitable for use on FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol VIPA-SP & SFC baseplates. Finally, because the reaction point for the installation tool has been moved to the head of the rail, the installer is able to lift sleepers (about 20mm) as part of the normal action of the tool, lifting from the rear arches of the clip before driving the clip into the installed position. NOTE: This tool has options avaialble under separate reference numbers; for variants with either insulated handles and / or cranked heads for confined spaces. The standard tool is always supplied with a straight head and steel handle. Optional variant of this tool using cranked head for confined spaces and insulated handle To insert the clips from the ‘Parked’ position of the shoulder as delivered from the sleeper factory, follow these instructions. The paddle should be in the normal front pivot hole and the side cheeks in the down position. (Different from the photograph) for ALL rail sizes. Locate the hooks on the side arms over the head of the rail. To insert the clips, grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip driving. Pull on the handle until refusal. The fully driven position for FASTCLIP ‘FC’ is achieved when the outer legs of the clip touch the rear of the side insulator in the shoulder, or with up to 3 mm of clearance. The FASTCLIP ‘FE’ installed position does NOT touch the shoulder or insulator. Once located the tool can be slid along the rail between sleepers for the next clip insertion. If the clip needs to be re-inserted from fully extracted, move the cheeks to the up position, to extend the reach of the tool. If more reach is required, the paddle can be moved to the rear pivot hole. Follow the instructions above.

ATEX - 225 LUMEN CREE LED ZONE 0 INTRINSICALLY SAFE IP67 1m SUB. HEADLIGHT 3 x AAA (NOT INC)

DATA SHEET

ATEX - 350 LUMEN CREE LED ZONE 0 INTRINSICALLY SAFE RIGHT ANGLE TORCH IP54 4 x AA (NOT INC)

DATA SHEET

ATEX - 150 LUMEN CREE LED ZONE 0 INTRINSICALLY SAFE IP67 3M SUB. FLASHLIGHT 4 x AA (NOT INC)

DATA SHEET

DATA SHEET

450 LUMEN CREE LED FOCUS ALUMINIUM FLASHLIGHT C/W WRIST STRAP AND IN A CLEAR HARDCASE DISPLAY BX - 4 x AAA DURACELL BATTERIES (INC)

DATA SHEET

200 LUMEN CRI "COLOUR-RENDER-INDEX" COB LED INDUSTRIAL IK07 SENSOR HEADLIGHT LIGHT WITH 3 COLOURS - 3.7v 1500mAh LI-PO INTEGRAL BATTERY - MICRO-USB CABLE (INC)

Single Head Tripod For Hexagon Site Lights

275 LUMEN SMD LED USB RECHARGABLE INSPECTION LIGHT WITH 250 LUMEN CREE TORCH IN TOP AND ROTATING MAGNETIC STAND - 3.7v 1600 mAh LI-ION INTEGRAL BATTERY - MICRO-USB CABLE (INC)