Insulated Simplex A17 Jack Handle
Insulated to BS8020

• Keying Hammer Head - 7lb / 3.2kg
• Hickory Handle
• Overall Length - Approximately 91.5cm

Insulated Keying Hammer - 7lb
Insulated to BS8020

SCRWC18 - 18mm

Genuine Rotabroach TCT Short Series Rail Cutter 18mm

STEL TCT Rail Cutter
TCTR30S - 30mm

• Emergency Serviceable G Clamp
• Suitable for Common Rail Profiles
• 95RBS BH/97.1/2 BH, 109/BS110A/BS113A FB, CEN60 E1/E2

Insulated Trenching Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 7" Wide x 11" Long

Tested For Live Work Often known as a '2-way' in some trades Used for digging and cleaning out narrow trenches for cable and pipe laying

Insulated Newcastle Treaded Shovel

Tested And Certified To BS8020:2011

Treaded Tested For Live Work 16" Long, 7" Wide Tapering to 4"

Often known as a 'grafter' in some trades.

Designed for digging deep and narrow trenches, channels and post holes.

Soft Indoor Sweeping Brush With Handle

• Sledge Hammer Head - 10lb / 4.5kg
• Hickory Handle
• Overall Length - Approximately 75cm

Insulated 7lb Sledge Hammer
Insulated to BS8020

CLAMP, UNIVERSAL, USED IN CONJUNTION WITH STEL IRONMEN,SUITABLE FOR USE ON UIC60, 113LB & BULLHEAD, RAIL TESTED TO 1500KG

CLAMP, SUITS 130 LB CONDUCTOR RAIL (64KG)

1 11/16" Bi-Square Fishplate Nut Spanner
36" BS8020 Fibreglass Insulated Shaft

Insulated Check Rail Spanner - 1-11/16" AF x 30" L
Insulated to BS8020

Insulated Hook Switch Pole
Insulated to BS8020

• Simplex A17 Jack Handle

• Conforms to BS8020 : 2011
• Keying Hammer Head - 10lb / 4.5kg
• Fiberglass Shaft
• Rubber Grip Handle
• Steel Protective Collar
• Overall Length - Approximately 92.5cm

• Sledge Hammer Head - 7lb / 3.2kg
• Hickory Handle
• Overall Length - Approximately 75cm

Mop Handle Blue

Mop Handle Red

• Keying Hammer Head - 10lb / 4.5kg
• Hickory Handle
• Overall Length - Approximately 91.5cm

Insulated Post Hole Digger Shovel Holder

46" HANDLE 

68" OVERALL LENGTH

INSULATED SLEDGE HAMMER 7LB

35" Overall Length

INSULATED HAMMER CLUB 2.5LB

10" Overall Length

INSULATED SLEDGE HAMMER 10LB

35" Overall Length

Rail Turning Bar - Insulated Bull Head
Insulated to BS8020

INSULATED HAMMER CLUB 4LB

10" Overall Length

Slewing Jack Handle Only

SUMO, BUILDERS / FENCING INSULATED SPADE 54" LONG HANDLE, OVERALL LENGTH 72" HEAD SIZE 5-1/2" X 14" LONG

SHOVEL, RABBIT / POST HOLE INSULATED HEAD SIZE 5-1/2" X 12" LONG 54" HANDLE, OVERALL LENGTH 72"

E Clip Replacement Hook 0039/42743

It is recommended for safety reasons that contractors should formally check and record the wear of the hooks at intervals of 6 months using the wear gauge.
The gauge is suitable for all types of Panpuller or e-Plus Panpuller.
The wear gauge provides easy Go/No-Go assessment of when to replace the hook.
Work hooks have a tendency to slip off the clips, which can present a significant risk to operators.

Spare Bolt For Pan Puller

INSTALLER, FASTCLIP FC, STEL VIPA-SP, SFC YELLOW / GREEN 0039/047850

Rear Arch Extraction Tool

Similar in design to the nine prong compost fork but more suited to heavy-duty work, the ballast fork is ideal for: Moving and loading stone, ballast and tarmac. Use by railway workers to transfer roadbed ballast.

Designed for use to facilitate the removal of old insulating pads from rail and sleepers.

All Steel Pot Dolly Hexagon 19mm

• Heavy Duty Digging Bar
• Hardened Steel
• 1.7 Metre overall length 

• Fassetta Bolt with Nut & Washer

• Tongs used for the safe manual handling and moving of Steel Sleepers.
• Built to be both durable and robust, they allow the rail worker to use them to re-position and remove steel sleepers as required.
• Insulated to BS8020.

• Schwihag Bar
• Used for inserting an extracting Schwihag clips

SCRWC21 - 21mm

Genuine Rotabroach TCT Short Series Rail Cutter 21mm

STEL TCT Rail Cutter
TCTR28S - 28mm

STEL TCT Rail Cutter
TCTR32S - 32mm

SCRWC19 - 19mm

Genuine Rotabroach TCT Short Series Rail Cutter 19mm

SCRWC20 - 20mm

Genuine Rotabroach TCT Short Series Rail Cutter 20mm

SCRWC22 - 22mm

Genuine Rotabroach TCT Short Series Rail Cutter 22mm

Blade Length 300MM X 3MM Thick

SCRWC23 - 23mm

Genuine Rotabroach TCT Short Series Rail Cutter 23mm

POLYFIBRE HANDLED CABLE LAYER SHOVEL TREADED, ONE PIECE HANDLE, 28"
PRODUCT SIZE; 5" X 4-1/2" X 11"

ALL STEEL FENCING SPADE EXTENDED HANDLE 
HEAD SIZE 5 - 1/2" TAPER TO 4 - 1/2" X 11"
OVERALL LENGTH 65"

PAVING MAUL, HARDWOOD HANDLE, RUBBER HEAD

Insulated Ferrule Extractor

STEL TCT Rail Cutter
TCTR23S - 23mm

STEL TCT Rail Cutter
TCTR22S - 22mm

SHC De-Clipping Bar

• Magnetic Retrieving Baton with Release.
• Magnetic Retrieving Batons are innovative and powerful tools to remove ferrous materials in wet or dry environments.
• Non-corrosive, stainless steel.
• Use of safety goggles and gloves is highly recommended when using this item.
• Ideal for removing hardware from storage bins.
• Clean water or degreasing tanks of metal shavings.
• Unique shape allows for easy pick up from walls and corners.
• Constructed with neodymium/rare earth magnets to maximize holding power.
• Pull to release collected material to dispose of.

Mop Handle Green

Diamondgrip Pull Cord Spool 3.6mm x 164ft

Insulated Treaded Round Mouth Shovel Shovel

Treaded

Tested And Certified To BS8020:2011

Handle - 28" / 711mm Blade Size - 10" Wide By 12.1/2" Long

Tested For Live Work

Used for excavating, diggiing and sovelling most aggregates. The pointed blade offers easier penetration in tougher ground.

Taper Mouth Steel Ballast Shovel

Used for shovelling out or concrete mixing, working tarmac and cement, backfilling trenches and manouvering ballast.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE:10" WIDE, TAPERING TO 8.1/2" BY 12.1/2'' LONG

Cable Laying Steel Ballast Shovel

PRODUCT HANDLE: 28"/ 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE: 5.1/2" WIDE TAPERING TO 4.1/2" BY 11" LONG

Trenching All Steel Ballast Shovel

Often known as a '2-way' in some trades.
Used for digging and cleaning out narrow trenches for cable and pipe laying.

PRODUCT HANDLE: 28"/ 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE : 7" WIDE X 11" LONG

Colour: Red working head (matches the appropriate e-PLUS clip type), and yellow handle. For use with eP20127 clips for retrofitting to sleeper types: F27, EF28, 5EF28, and for the new S&C designs to NR56V. All STEL hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 32mm diameter cylindrical straight handles Installation Instructions • Insert center leg of clip into housing. • Place pivoted hook over the inside of the front arch of clip with foot of PANPULLER behind clip housing and ensure lip of the hook is under the front arch. • Taking up a natural stance with feet apart, move one leg half a pace back to prevent loss of balance. Stand behind the PANPULLER, with both hands on tee handle at top of PANPULLER, pull strongly towards chest until refusal. • The PANPULLER automatically pulls clip to the correct position When correctly installed the centre leg of ALL types of e-PLUS clips, protrude beyond the shoulder to hold the side-insulator in the correct position. This tool is 'handed' to hold the insulator in position during clip insertion. This means that the tool cannot be used for extraction of the clip. To extract this e-Plus clip use a standard PANPULLER Type LP1180

Suitable for use on FASTCLIP FC, FASTCLIP FE, VIPA-SP and SFC fastenings. The new tools, which react from the rail, are more efficient, faster and safer because they are not prone to slipping from the shoulder reaction points. Additionally, the tools offer compatibility with a wide range of Pandrol systems, including FASTCLIP ‘FC’ & FASTCLIP ‘FE’ and the Pandrol VIPA-SP & SFC baseplates. Finally, because the reaction point for the installation tool has been moved to the head of the rail, the installer is able to lift sleepers (about 20mm) as part of the normal action of the tool, lifting from the rear arches of the clip before driving the clip into the installed position. NOTE: This tool has options avaialble under separate reference numbers; for variants with either insulated handles and / or cranked heads for confined spaces. The standard tool is always supplied with a straight head and steel handle. Optional variant of this tool using cranked head for confined spaces and insulated handle To insert the clips from the ‘Parked’ position of the shoulder as delivered from the sleeper factory, follow these instructions. The paddle should be in the normal front pivot hole and the side cheeks in the down position. (Different from the photograph) for ALL rail sizes. Locate the hooks on the side arms over the head of the rail. To insert the clips, grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during clip driving. Pull on the handle until refusal. The fully driven position for FASTCLIP ‘FC’ is achieved when the outer legs of the clip touch the rear of the side insulator in the shoulder, or with up to 3 mm of clearance. The FASTCLIP ‘FE’ installed position does NOT touch the shoulder or insulator. Once located the tool can be slid along the rail between sleepers for the next clip insertion. If the clip needs to be re-inserted from fully extracted, move the cheeks to the up position, to extend the reach of the tool. If more reach is required, the paddle can be moved to the rear pivot hole. Follow the instructions above.

STEL TCT Rail Cutter
TCTR19S - 19mm

CABLE GUIDANCE TOOL, 37", INSULATED, USED IN CONJUNCTION WITH TROUGH LID LIFTER

• Tongs used for the safe manual handling and moving of Steel Sleepers.
• Built to be both durable and robust, they allow the rail worker to use them to re-position and remove steel sleepers as required.

All Steel Square Mouth Shovel intended for shoveling out, concrete mixing, working tarmac as well as cement, back filling trenches and maneuvering ballast.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE: 10'' WIDE X 12.1/2" LONG

STEL TCT Rail Cutter
TCTR26S - 26mm

Insulated Cable Laying Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 5" Wide Tapering to 4.1/2" By 11"

Long Tested For Live Work Often known as a '1-way' in some trades.

Designed for cable and pipe laying with a slim blade that is ideal for digging out narrow trenches.

This all steel grafting tool has a dished blade and a curved cutting edge which makes it ideal for clay digging and heavy ground breaking work.
It has a forged blade, tubular steel shaft and steel YD grip with wooden cross piece for added comfort.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE: 6" WIDE X 12" LONG

This all steel Newcastle draining shovel has a forged blade, tubular steel shaft and steel YD grip with wooden cross piece for added comfort.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE : 7" WIDE, TAPERING TO 4" BY 16" LONG

This all steel round mouth shovel has a forged blade, tubular steel shaft and steel YD grip with wooden cross piece for added comfort.

Used for excavating, digging and shovelling most aggregates. The pointed blade offers easier penetration in tougher ground.

PRODUCT HANDLE: 28"/ 711MM ALL STEEL MYD

PRODUCT SIZE: BLADE: 10" WIDE X 12.1/2" LONG

This all steel rabbit shovel has a forged blade, tubular steel shaft and steel YD grip with wooden cross piece for added comfort.

PRODUCT HANDLE: 28" / 711MM ALL STEEL MYD

PRODUCT SIZE: 7" TO 5"X 12"

Length 112cm
Width 15cm
Weight 2.5kg

Solid Steel Crowbar with Chisel & Point Ends - 28mm Round X 1500mm Shaft

Solid Steel Crowbar with Heel & Point Ends - 1 1/8" Hexagonal X 5 Foot Shaft

Insulated Chisel & Point Crowbar/Digging Bar

• Insulated Heel & Point Crowbar
• 60" Insulated Solid, Non-Conductive Fibreglass Shaft with Forged Steel Ends
• Conforms to BS8020
• Quote MM0001 when ordering over the phone to receive our special price of £35 (exc vat)
• Tested up to 10000V
• Safe for up to 1000V 
• 1.5M 
• 6KG

A durable, insulated wheelbarrow fabricated from a rugged single mould polyethylene material ideal for use on rail possessions and also utilities. 

• The STEL Insulated Wheelbarrow has a puncture proof tyre, also a double skin with 6mm walls made of Polyethylene to ensure maximum durability.
• No metal core parts are used resulting in the insulated wheelbarrow being a safer option for use in areas where conductivity may be an issue.
• The STEL insulated wheelbarrow is commonly used on or around 3rd rail / conductor rail working environments for safer working within possession zones.
• The STEL insulated wheelbarrow is also used for the application of cable laying.
• Our insulated wheelbarrow is robust with re-enforced handles and an extra strong tipping bar located in front of the wheel.
• Designed for the outside, the insulated wheelbarrow is rust free with a one piece mould construction resulting in fewer stress points.

• Capacity:      90L / 20 Gallon (Approx)
• Weight:        12kg (Empty)
• Dimensions: Length: 1540 x Width: 615 x Height: 620mm

Require more than one unit? Please call or email our sales office to request a quotation with respect to a multiple purchase discount.

Enquire today - Tel: 0114 383 0110 or email: sales@specialisedtools.co.uk

Insulated Taper Mouth Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 10" Wide By 8.1/2" Tapering To 12.1/2" Long

Tested For Live Work Used for shovelling out or concrete mixing, working tarmac and cement, backfilling trenches and manouvering ballast.

Insulated Square Mouth Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 8" Wide By 10.1/2" Long

Tested For Live Work Used for shovelling out or concrete mixing, working tarmac and cement, backfilling trenches and manouvering ballast.

Insulated Rabbit Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 7-1/2" Wide By x 11-1/2"

Tested For Live Work Ideal For Transplanting Plants And Shrubs And Also For Post-Holing Jobs

Insulated Clay Grafting Shovel Treaded Shovel

Tested And Certified To BS8020:2011

Handle - 28" / 711mm

Blade Size - 6" Wide By 12" Long T

ested For Live Work With a slightly dished blade and round cutting edge, designed for clay digging and heavy ground breaking.

Insulated 1.5M Point End Crowbar

• Insulated Point End Crowbar
• Insulated Solid Fibreglass Shaft
• Conforms to BS8020
• Rubber Grip for Extra Comfort
• 32MM Ø X 57" Long

Insulated Heel End Crowbar

• Timber Nips used for the safe manual handling and movement of Timber Sleepers.
• A durable and robust tool

• Rail Tongs manufactured from forged steel.
• Designed to accommodate a range of rail sections.
• Hi-Vis Yellow

All Steel Extractor Ferrule

• Insulated Pot Dolly Hexagon 17mm For Concrete

Jack Handle - Pan Jack, Toe Jack, Zwicky / Kenhi

Insulated Chisel End Crowbar

• Conforms to BS8020
• Certified to 1000 Volts - Tested to 10000 Volts
• Solid forged from one piece of steel
• YD handle
• Strong yet lightweight fibreglass shaft has excellent insulating properties
• Lightweight at just 2.5kg
• BS8020:2011

Designed for use to facilitate the removal of old insulating pads from rail and sleepers.

Insulated Type E Clip Pan Setter

Cat No Reference: 0039/47852 Suitable for use on FASTCLIP FC and FASTCLIP FE The original version of the sleeper lifter can still be used in conjunction the new installer where sleepers need to be lifted more than 20mm. Instructions for Sleeper Lifter LP12608 The scissor action of the frame opens in order to locate the pincers of the tool into the sides of the shoulder with the clip in the ‘Parked’ position. Place the hook of the tool over the head of the rail, and as the body of the tool rises the scissor action closes the pincers and lock into the shoulder. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during sleeper lifting. Push the handle away to lift any ‘dropped’ sleeper if ballast conditions do not support the sleepers engaging with the foot of the rail. These tools should be used in pairs to lift the sleeper to locate both rails simultaneously with the rail seats of the sleeper. The sleeper lifter can used on the same rail seat as the FASTCLIP installer, by locating between the hooks of the installation tool.

TYPE FAST CLIP FC EXTRACTOR - FRANCE TYPE FASTCLIP FC OUTIL MANUEL D'EXTRACTION

Catalogue No; Reference: 0039/42748 PANDROL No. LP1180. And for 4 shoulder baseplates. All STEL hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 32 mm diameter cylindrical straight handles, Instructions for PANPULLER LP1180 ​• Insert center leg of clip into housing. • Place pivoted hook over the inside of the front arch of clip with foot of PANPULLER behind clip housing and ensure lip of the hook is under the front arch. • Taking up a natural stance with feet apart, move one leg half a pace back to prevent loss of balance. Stand behind the PANPULLER, with both hands on tee handle at top of PANPULLER, pull strongly towards chest until refusal. • The PANPULLER automatically pulls clip to the correct position Extraction Instructions Reverse the PANPULLER • Taking up a natural stance (feet apart, move one leg half a pace back to prevent loss of balance) on the same side as for installation, place hook on the outside of the front arch of the clip, the foot of the PANPULLER resting on the baseplate/housing just above the centre leg of clip (as illustrated). • Standing behind PANPULLER with both hands on the tee handle at the top of PANPULLER, give a strong firm push away from your chest. • If clips have been in situ for many years, it may be necessary to use a hammer to loosen them taking safety precautions. If the clips will not move then use the Rusty Clip Extractor can be used for PR clips. NOTE. It is mandatory to wear eye protection when removing or fitting any clips where hammer assistance might be necessary.

Insulated Type E Clip & PR Clip Pan Puller

Cat No; Reference: 0039/42900 The PANSETTER is suitable for all Network Rail Sleepers fitted with PR, e & e-PLUS. Used for lifting the sleeper to the rail foot. It pushes the rail over, leaving the correct gap between the rail foot and the Pandrol housing, so that the insulator can be easily placed in the correct position. All Pandrol hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 35mm diameter cylindrical handles with ‘T’ cross bars for improved ergonomic and safer use.

No. AE17256 formerly No. LP15923

Colour: White

The tool is used with the eP20129 green or eP20130 yellow e-PLUS clips, mostly with RT60 and NR60 S&C layouts.

PAN PULLER, E PLUS, HOOKS CASE HARDENED TO 45-50 HRc PAINTED BLACK 0039/042742

EXTRACTOR, FASTCLIP FC, STEL, CREAM/GREEN 0039/047851

• Constructed from durable steel 
• Use on BS113A, UIC 60, S46 & S54 Rail Section
• Length - 1.4 meters

15" Fishplate Nut Running Spanner, used for the quick release of fish plate nuts. The length of the handle allows the railway worker to quickly remove or tighten the nuts.

Rail Turning Bar - Steel Bull Head

SPANNER, FISHPLATE, NUT LOCKING, 30'' LONG 1-11/16" AF (43MM) FOR 1-5/8" SQUARE NUTS STANDARD 0039/058605