ATEX - 150 LUMEN CREE LED ZONE 0 INTRINSICALLY SAFE IP67 3M SUB. FLASHLIGHT 4 x AA (NOT INC)

DATA SHEET

DATA SHEET

Catalogue No; Reference: 0039/42748 PANDROL No. LP1180. And for 4 shoulder baseplates. All STEL hand-tools can be supplied with optional insulated handles, which have recently been upgraded to 32 mm diameter cylindrical straight handles, Instructions for PANPULLER LP1180 ​• Insert center leg of clip into housing. • Place pivoted hook over the inside of the front arch of clip with foot of PANPULLER behind clip housing and ensure lip of the hook is under the front arch. • Taking up a natural stance with feet apart, move one leg half a pace back to prevent loss of balance. Stand behind the PANPULLER, with both hands on tee handle at top of PANPULLER, pull strongly towards chest until refusal. • The PANPULLER automatically pulls clip to the correct position Extraction Instructions Reverse the PANPULLER • Taking up a natural stance (feet apart, move one leg half a pace back to prevent loss of balance) on the same side as for installation, place hook on the outside of the front arch of the clip, the foot of the PANPULLER resting on the baseplate/housing just above the centre leg of clip (as illustrated). • Standing behind PANPULLER with both hands on the tee handle at the top of PANPULLER, give a strong firm push away from your chest. • If clips have been in situ for many years, it may be necessary to use a hammer to loosen them taking safety precautions. If the clips will not move then use the Rusty Clip Extractor can be used for PR clips. NOTE. It is mandatory to wear eye protection when removing or fitting any clips where hammer assistance might be necessary.

3-IN-ONE’s original drip oil lubricates, cleans and prevents rust. Its precise, easy-to-use drip spout enables precise lubrication, with no overspray or splatter. It can be used on in-line skates, tools, bicycles, wheels, fans and moving parts

A multi-purpose product which actively displaces water leaving an electrically non-conductive barrier
Penetrates rust and corrosion by capillary action, loosening rusted parts
Protects metal against rust and corrosion
Cleans away grease and grime
Leaves a protective film of lubricant
5 Litre Plastican with Spray Bottle

Safety Data Sheet -

FORCE Brake & Parts Cleaner
Quantity: 6
Used for cleaning all parts of braking systems
Cleans without dismantling
Dissolves grease & oil
Size: 400ml Aerosols

FORCE Carb & Fuel Injector Cleaner
Quantity: 6
Info: Cleans & de-greases all engine parts
Removes gums, oils & grease
Compatible with catalytic converters
Size: 400 ml Aerosols

• Graphite cast iron load sheave
• Hand lever made of malleable cast iron or tubular steel model with rubber grip
• Automatically acting load pressure brake
• Free chaining device optional
• Drop forged load and suspension hooks
• Asbestos-free friction discs

Yale Hand Lever Hoists are versatile, portable units for pulling, tensioning, lashing and lifting loads. The operation of the Hand Lever Hoists is easy and safe.
Light weight, robust malleable cast iron model, free chaining, slip clutch, stamped steel - or aluminium housing, low operating effort - in the Yale product range you will always find an optimal hoist for every type of operation.
The brake system of all Yale hand lever hoists are based on the original Yale patent of the British Engineer Thomas A Weston dating back to 1875. All parts of the load brake are made of high quality materials and are protected against corrosion.
The graphite cast iron load sheave for the link chain has precision machined chain pockets for accurate fit and durability of the load chain. The roller chain sprocket is made from heat treated chromium-molybdenum steel with precision machine teeth to ensure smooth chain movement.
Every Yale ratchet lever hoist is factory tested with overload. The units are supplied with a test certificate showing the serial-No. Operating instructions which contain an EC declaration of conformity are also attached to each unit.

• Minimum Space Required in Vehicle
• Support Arm Works as Stabiliser during Loading and Unloading
• Reduce potential injury and fatigue to operator
• Doesn't have any influence on axel counters, even when they are not correctly adjusted (set over height)
• Safe and efficient method of transporting tools and smaller plant equipment to worksite
• Width - 360mm
• Length - 870mm
• Height - 190mm (without push handles fitted)
• Height - 820mm (with push handles fitted)
• Weight - 13.6kg (without push handles fitted)
• Weight - 17.8kg (with push handles fitted) 
• Safe Working Load - (NWR Spec) 250kg
• Safe Working Load - (LU Spec) 75kg
• BS EN 13977:2011 - Railway application - Track - Safety requirements for portable machines and Skate Baskets for construction and maintenance.
• RIS 1701 PLT - Rail Industry Standard for Portable and Transportable Plant Used for Infrastructure Work.

Cat No Reference: 0039/47852 Suitable for use on FASTCLIP FC and FASTCLIP FE The original version of the sleeper lifter can still be used in conjunction the new installer where sleepers need to be lifted more than 20mm. Instructions for Sleeper Lifter LP12608 The scissor action of the frame opens in order to locate the pincers of the tool into the sides of the shoulder with the clip in the ‘Parked’ position. Place the hook of the tool over the head of the rail, and as the body of the tool rises the scissor action closes the pincers and lock into the shoulder. Once located grasp both handles of the ‘Tee’ bar, and stand ‘naturally’ with feet apart then move one leg half a pace back, to prevent loss of balance during sleeper lifting. Push the handle away to lift any ‘dropped’ sleeper if ballast conditions do not support the sleepers engaging with the foot of the rail. These tools should be used in pairs to lift the sleeper to locate both rails simultaneously with the rail seats of the sleeper. The sleeper lifter can used on the same rail seat as the FASTCLIP installer, by locating between the hooks of the installation tool.